Jump to content
SAU Community

Recommended Posts

there are heaps of skylines out there missing those stickers

Yeah.. heaps of accident repaired skylines...

Under the old import rule, it is a known practice to import accident damage vehicles from japan at cheap prices, repaired them here before selling. Because the cost of accident repair here is cheaper than in Japan, this is a way to make profit. The new SEVS rule makes it harder for these dodgy skylines to make their way into the country because accident damage vehicles can no longer be imported unless a good quality accident repair has been done in Japan before the car is imported. Although this doesn't mean that imported cars under the new SEVS rule (excluding 15yo cars) do not have accident damage in Japan, however the new rule would reduce such "dodgy" practices that were usually done in the past. The catch is, it is now harder & more expensive to comply imports because the control is very strict in terms of damaged and modified cars.

Hmm.. you said: The only way to remove the sticker is by respraying the car??

Why would anyone wanna remove factory badges/stickers? It will only reduce the value of your car no matter for whatever "cool" or "rice" reason you got...

When cars are being resprayed, the painter will need to remove any stickers on the panel they're working on. Nobody spray over sticker, it will show up and final result won't be good. Masking the sticker (as some dodgy painter did) will not yield in better result in the long time, as paint will peel or have rough edges around the sticker where they masked it off.

Get a new sticker from Nissan, I'm sure they can get you from Japan. Try Blackburn Nissan (see other thread about this)

My car doesn't have the sticker either, and no idication that it ever did. Also, being a series II the bonnet mounted S logo was taken off (which i later found in the glove box, Thankyou Japanese owner! :D) I'm 99% sure my car has never been resprayed either.

My car doesn't have the sticker either, and no idication that it ever did. Also, being a series II the bonnet mounted S logo was taken off (which i later found in the glove box, Thankyou Japanese owner! :D) I'm 99% sure my car has never been resprayed either.

There's a way to remove sticker without marks is to clean it afterwards and buff it out, maybe cut and polish will do.

Have you had an experienced panel beater have a look at your car? You might be surprised how easy they can spot and point out proof of respray on things that would normally be missed by common people like us... A panel beater showed the proof on mine, I was shocked as I never paid attention on that part until he pointed some little details of previous respray job. However he praised that it is a good quality repair, so it should be ok. :)

yeah, my car had been buffed when i first bought it. I'm glad the logo wasn't on the bonnet tho, i had a fear that if it was there some idiot might try and rip it off. I remember when i first started looking for Skylines i came across a series 1 in a car yard where someone had taken off the badge with a screwdriver... not good.

mine is still on there and its looks fine to me, and my uncle is a panel beater and has not said that my car has any repsrays or anything when he put was buffing out some scrathces and painting my bodykit and stuff.

Besides, i would like to keep the GTS25T sticker on there, and not be like people who take it off and throw gtr badges front and rear... (no ill feelings towards people who take them off and keep it plain though)

absolute rubbish about it reducing your resale value. I have noticed those gts 25t stickers on most skylines have faded and become weathered, and as far as i'm concerned, they look very ugly when they are cracking. I peeled mine off. It did leave a residual mark, but that's better than having the sticker there. Just whack a small nismo sticker in it's place.

i agree with 97r33gtst-typeM

my first 95 r33 came from japan with a really weathered gts25t sticker so i removed it

my current line came without the sticker

they all come factory with it, but over time they do fade and crack, and lots of people just like the debadged look.

i am planning to peeel that sticka off...just for the plain slick look, so that my car is stickerlesss....umm anyone know a way to peeel it off without leaving a mark?

I read somewhere in this forum a while ago that if you use a blow dryer, the sticker will come off much easier...anyone have experience with this?

Mine is now missing that sticker as it has been resprayed.

If you want another they can be had from Nissan for around $40.

You will need to supply your paint code so they can match up the correct sticker for you.

I am thinking of getting a new sticker, make it have that fresh out of the factory look.

BUT.. I have better things to spend $40 on. ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...