Jump to content
SAU Community

Recommended Posts

19 minutes ago, joeyjoejoejuniorshabadoo said:

 

 


So you were running about the same power as my car which would have 0% traction loss with 8kg rears and less suspension work...

 

Yep, but your power came in way later. I have 4KG rears with helper springs, a Nismo 1.5way diff, running -1deg camber and AD08R's which were up to temp and running 30psi hot.

Not saying it's the best setup in the world, but it's not like it's a slammed 15KG rear springed 2 way on stretched 195 nankangs that cost $4 each :P

Yeh the other thing that I gotta keep in mind is the falcons are sensitive to diameter, like if the fronts have 650mm diameter and the rears have say 600mm (an example) traction control light just goes nuts thinking its spinning all the time, which is annoying because the 265/30 is cheaper than the 275/30s but the diameter is slightly smaller and don't want to have those annoying ass problems.

So I stick to tyre sizes I know look good and work 

Edited by UNR33L
  • Like 1
1 hour ago, UNR33L said:

True, I mean I just copied pasted the emails but yeah. Finding sticky tyres in 19s with the right sized sidewalls, a lot of makes just make them big sidewalls which I don't really want (like a 245 / 40 as oppose to a 245 / 35) Invos / RS3 / NT05s / AD08s much harder to find them in the sizes I want, and if I do sometimes the prices are just stupidly high compared to the 'thick side wall' of the same tyre. Anyway seems st george are probably my best bet

Go with the more common one. remember sidewall is a % of the width too, not a direct measurement

1 hour ago, Kinkstaah said:

Yep, but your power came in way later. I have 4KG rears with helper springs, a Nismo 1.5way diff, running -1deg camber and AD08R's which were up to temp and running 30psi hot.

Not saying it's the best setup in the world, but it's not like it's a slammed 15KG rear springed 2 way on stretched 195 nankangs that cost $4 each :P

was your microphone broken Mr Trump?

1 minute ago, JAS-25T said:

who does lifts from the airport to city for less than the skybus?

isnt it like $18 a trip? i dont bring the gloria out for less than $50 unless im already in the area.

13 minutes ago, HEKT1K said:

 


Lack of PT from the airport is balls

I'd be happy to give up the most liveable city title for a year or two to get this done

 

yet neither liberal or labor will do it.... 

we need Kennett back... Kennett would have done it if he had time 

5 hours ago, Kinkstaah said:

Yep, but your power came in way later. I have 4KG rears with helper springs, a Nismo 1.5way diff, running -1deg camber and AD08R's which were up to temp and running 30psi hot.

Not saying it's the best setup in the world, but it's not like it's a slammed 15KG rear springed 2 way on stretched 195 nankangs that cost $4 each :P

What was your top speed out of Curiousity?

 

1.29 aint a bad time in a sedan auto

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...