Jump to content
SAU Community

Recommended Posts

I'm looking to upgrade to something bigger in-tank, but the thought of the noise is a bit off putting. The car is an R33 GTS-T and would be making probably 200-250kw in the near future.

So, very simply, what brand/model of upgraded fuel pump did you find to be acceptably quiet?

And conversely, what pumps did you get that were excessively noisy?

Begin!

First mod I did was to upgrade from stock to Nismo fuel pump, went from inaudible to a slight buzz, and back to inaudible as soon as my exhaust was upgraded, and its a quiet exhaust. The car was a 32gtst not a 33.

I run the E85 Walbro pump, as it's a modern design it's very quiet... it's quieter than my old Tomei pump in my previous R33, however it will heat up your stock wiring like a boss.. I have installed 12gauge wiring from the battery to a 40AMP relay to the fuel pump and earthed the pump directly, bypassing all that FPCM business.

Ive had nearly every fuel pump known to man hahaha, at least 10 different types i can think of, by far the quietest was the Denso 265l/ph intank i just took out of my 33, was silent. The 040 that was in there previously was a bit louder. Happily supported 270 kw. Have just gone to a pair of solid mounted 044's, fed by a pierburg in tank e85 specific lift pump for 350kw +. Could have done it with an in tank, but is now race car so not an issue.

I also had an R34 GTR pump that was barely audible and supported a 250kw SR20. Had a Nismo in tank as well and although you could hear it, wasn't offensive in the slightest. I had a walbro 255 in my R31 and it was pretty noisy?

For the money, denso is the go. Think i paid $150 for my denso new, probably less. Is also straight fit. For your power level i think the walbro 460 is a bit overkill.

Side note: I have an A1000 in another car, and that vid does the noise no justice. It's seriously the loudest fuel pump I've ever heard!

Edited by R31 drift pig

Cool. I think walbro or denso might be the way to go. Anyone know what kinda max power the 265/255 Lph etc can handle?

Depends on a lot of variables, you need good voltage to it with thick wires, and your fuel pressure and boost has a lot to do with flow output.

I would usually expect 300kw on e85 or 400kw on 98 from the Walbro 255's.

External pumps like the bosch 044's need a bit of head pressure on them, quietens them down immensely, and to have no restriction before their inlet, ie being bolted straight to the surge tank with the largest fitting possible, and fitting a check valve in the return line that opens around 20psi (irrelevant though to your question)

The good thing about an intank pump is that its immersed in fuel and generally external to the cars cabin, if its bad enough, a small roll of sound deadener mounted around the boot and tyre well will really reduce the noise.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...