Jump to content
SAU Community

Recommended Posts

Hi guys,
I joined up here a few years ago when I used to own an r-33 GTR, this community has been really helpful in the past and obviously has a lot of experienced with modified cars & blue slips. I desperately need advice on my current situation.

I live in Sydney & own a 2000 SUBARU IMPREZA WRX, which I foolishly allowed to run out of rego (wasn't driving it often, money pretty tight), I didn't realise it would be so difficult to get a blue slip for a modified car.

My mechanic down the road quoted me $2250 all up (wtf?) to put it back to stock and do the following work (obviously he's a completely by the book guy, possibly over-quoted as well):

- pedal rubbers (the pedals are aftermarket lol)
- check off valve

- exhaust (its a half system)

- NISIR stop light (not sure what NISIR means, but he said the stop light was out)
- Oil leaks
- Radiator support panel bent (I hit a bump in the road pretty hard about a year back damaged the front lip of the car, so I assume that's what its from)
- Headlight covers (presumably not a big deal)

Where should I take it (around Sydney) and what's the best approach to get a blue slip for the least amount of money possible? The main issues are obviously the exhaust, the check off valve and the bent radiator panel, nothing else seems major. I can't afford to put thousands of dollars into a car that's worth ~5k. That being said the car is reliable and has plenty of years left in it. I also really can't afford a new car either. Is an engineers certificate my only option? Please help!

Link to comment
https://www.sau.com.au/forums/topic/460257-blue-slip-woes-sydney/
Share on other sites

The brake light is actually n/s/r which is Near Side Rear or passenger side

When I bought my my00 wrx up from Victoria it had a full exhaust and a boost gauge and the blue slip place passed it.

whats a check off valve? (I'm assuming it's a blow of valve), if so I have one you can borrow

If the blow off valve vents to atmosphere, most probably won't pass it.

Borrow a plumb back version from someone.

Unless the exhaust is obnoxiously loud, shouldn't be a problem.

Degrease the oil leaks just before you get it checked, should only fail if it drips onto the ground during the inspection.

Unfortunately, there is no set inspection time, so they technically could leave it for 4hrs and say that was the inspection period.

Most aren't dicks like this.

Take the aftermarket pedal off the brake and reinstall after the check (if they're just the ones that sit over the pedal).

The bent support shouldn't be an issue.

  • Like 1
  • 3 weeks later...

agreed mate, you are going to have to shop around for blueslip.. I had to transfer my rego from WA to NSW not long ago, went to a couple of blue slip shops and get quoted ridiculous prices.. this is after doing the straight forward stuff myself like plumback BOV, std exhaust, car height.. was picked up on stuff like heater core.. i feel that there is a lot of grey areas needs to be covered in the handbook.. basically if they want to get you done, they can.. best of luck..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...