Jump to content
SAU Community

Recommended Posts

im all for collecting weird/wonderful/rare car parts and accessories, but when I go into a Nissan dealership and see a display for Nismo clothing or flick through an options list for a 370Z or R35, theyre all just wank. Nismo has turned into basically how Ferrari keeps itself afloat: selling hats and sports jackets.

All the cool bits and pieces SAU carries on about are from yesteryear mainly, when well engineered parts and racing pedigree were more important than bling or ridiculous pricetags. I imagine someone in Nismo saw how much LMGT's are selling for and thought "hmmm wonder how much we could charge for a size that suits R35?"

  • Like 1

You could pay for a TIG welding course and do a few hundred hours of practice for 50% of what it costs to buy that R35 exhaust, then buy some Ti and make one up yourself and still spend less in time and capital, arguably benefiting yourself a hell of a lot more than just buying the brand bling.

Or....you could buy or build something that was 10% of the bling and weighed 20% more and possibly get at least all the same performance benefit at 20% of the outlay.

A nice ti exhaust for a 32 is at least $2500...

% wise of the value of the car they are equal.

So I will say again. Just because his don't see value doesn't mean it's shit.

but it is shit when it doesn't perform as good as a product that costs less than half.

nobody is doubting the build quality of the stuff.

but 21k is farking stupid for some robotically welded (low grade) titanium tube that would have cost nissan maybe 1000 bucks in material.

No offence but anfanee is delusional if he believes nismo is worth the money when all they do is rebadge other products.

Mate you bought a 33. Why didn't you spend thousands less and get a car that's faster?

Oh because you wanted a 33? Oh OK.

But because I don't see the value it's shit.

#greatlogic

I'm just pointing out the logic tbh. Like I said just because you don't see value doesn't mean it's shit.

If you only look at "value" why did you buy a 33?

If you are only interested in increases why did you buy the heavy brother?

Why? Because you wanted one. But people don't sit there preaching that they are shit.

Off ye high horse and just accept everyone has different tastes and respect those tastes.

What have i done...?

I'm with the "buy parts that are good value camp".

Also, I liked how the 1700 buck nismo key became a 2000 buck nismo key after a few hours.

Apparently there is one on ebay for 330 bucks right now btw

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...