Jump to content
SAU Community

Help Wanted For Tuning

DPham

By DPham,
in General Automotive Discussion

 Share

Recommended Posts

DPham Explorer

DPham

Posted
Posted

Hi Guys i am quite new to the car scene i recently just purchased a 180 shell which i overpaid for quite a lot for since i didn't really know anything about cars. Previously i owned a honda integra dc5 type S which was both my daily and weekender toy. I have currently purchased over 10 grand in second hand parts which have not even been installed yet. The shell has a fair bit of rust when i purchased the shell as did not check under it as i was suggested to buy this shell by my best mate who owns a black s2k . I'm planning on paying for a 3 grand respray which includes dent repair and rust repair. There is a hole caused by the rust underneath the chassis but i was told that a plate is going to be welded to it so it should be fine. So far i have spent 12k on the car and it is still not running right to the way i want as it is in need of an oxy sensor and afm.

I am only a P plate driver so i want to keep the car P plate legal. I want the car to make at least 250kw at the rears and i am willing to pay for parts needed. I was told sr20de engines easily make 400kw. I was told of several places that can do this is Garage worx, Edge motorworks, Jak motorworks and Chasers Motorworks as these shops are considered nissan specialist and can dyno tune my car for 250kw.

i don't really trust jak and chasers so i won't take my car to them. I would like your thoughts on Garage worx and edge motorworks.

Link to comment
https://www.sau.com.au/forums/topic/461505-help-wanted-for-tuning/
Share on other sites
Leroy Peterson Grand Master

Leroy Peterson

Posted
Posted

If you run space savers on the rears it will feel like it makes 250kw.

But seriously its not worth the time or buckets of money to get that kind of power from NA. Buy turbo bits then wait till youre old enough. A $3k respray is going to be fairly shit, and thats not even including dint or rust repair.

Hertz Donut Proficient

Hertz Donut

Posted
Posted

SR20DETs can make 400kW. SR20DEs, you'll be spending a lot of money to make 200kW. A "T" makes a big difference.

Now, I'm from a small set of islands far off the East coast of Aussie, but from what I understand "over 10 grand in second hand parts" and "P plate legal" don't really go hand-in-hand, unless maybe that's all stereo gear or a very, very fancy set of wheels that will go missing in about 4 weeks' time. I thought engine mods were pretty much a no-no?

Birds Grand Master

Birds

Posted
Posted

OP, you're getting "told" a lot of things and spending money on hearsay. Stop listening to friends and start reading or asking professionals.

Agree with above; cut your losses any way you can. Accept you made a mistake and move on. Dreams take time and you're rushing in gung-ho. Buy a decent n/a car for your P plates and then sell it. Then buy a decent turbo car. Do nothing but this.

3k with dent removal will be a shit job unless part of the deal is you're doing the spraying yourself...in which case it will be a shit job.

DPham Explorer

DPham

Posted
  • Author
Posted

Thanks for the advice guys...

I have contacted Garage worx and they told me not to give up hope on the car. They told me i can still be restored and since I've already spent so much on it i shouldn't really cut my losses just yet. Garage worx told me to proceed with the 3k respray and repair as they told me it's a really good quote so i will be getting the car resprayed next week.

DPham Explorer

DPham

Posted
  • Author
Posted

Sweet.

Post pics please. Before and after the plate gets welded over the chassis rust.

Is the shell rego able?

i'll try to get some photos in

i think the shell is able to be regoed, when it was a det, it was once regoed so i'm pretty sure it can be regoed

Hertz Donut Proficient

Hertz Donut

Posted
Posted (edited)

Oh lawd. Stop. Stop stop stop stop stop.

Stop.

"I think" doesn't cut it when it comes to rego, unless you intend to keep it off the street, permanently. Find out FOR SURE if it's still able to be rego'd before doing ANYTHING else. There's no need to rush through this, you'll only get further in the hole.

I really hope this works out for you, but you need to step back and do some due diligence before carrying on.

Edited by Hertz Donut
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • uchoa
      Yet another RB Neo misfiring thread after reading all the others.

      By uchoa · Posted

      Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
    • MBS206
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By MBS206 · Posted

      Ha ha ha, so they stopped the bearings spinning on the one you want, but then decided the crank hub should slip instead 😛   Stick to RB, at least you can work on it yourself. And now it doesn't smell of vapour   Also I still believe there's a chance your new flap doesn't "pop", as even though the engine might breath hard, it has a direct path with no restriction to the inlet, which when on boost should pull a bit of suction for you. If you do get pressure in the catch can id be very intrigued. Time to put a boost gauge on it, and a session at the track, then solid cover your vent and do another session
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Oh nah, S55 doesn't eat bearings, just the crank hub slips lol.
    • Milkmun
      The Evolution Of "night Fury"

      By Milkmun · Posted

      When’s the tow ball on the 33 coming? 🙃
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      I welcome any basic question that can help haha. Yes it has 2 unis but the driveshaft is a one piece and the unis are welded without a slip yoke at each end.   What's funny is anytime I've ever had wheel vibrations it's always been in the front so I automatically assume it will lead to steering wheel shake and not chassis vibration. With that being said, I never considered looking at my rear wheel balance... I have doubts though as this wasn't an issue before I pulled the motor and trans but is still very much worth a look. I'll do that tonight after work. Thanks. 
×
×
  • Create New...