Jump to content
SAU Community

Recommended Posts

Good morning all.

My R32 GTR is now no longer on daily duties and has become the weekender it deserves to be. This amongst some other things has prompted me to look into freshening up my insurance policy. I for one do not like to be the that guy who gets caught out if the worst were to happen to my car.

as we all know recently the USA has started to take all the Japanese export R32 GTRs and have driven the price up allot as expected. as their limitations lift over the next few years the R32 and R33 GTRs will get harder to replace.

this can be seen already, I have just done a search on carsales. 2 years ago the average value would have been $17-23k. some cheaper bad examples, some higher priced ADM and highly modified cars.

now, and have a look for yourself. the cheapest 32gtr is $24000... that's the cheapest. the average is now as im writing this post $34000. that's the average taking out anything over $50k or ADM.

Mine is clean and relatively unmodified... its at least still insurable. so if I were to replace my GTR I would expect, if i bought from carsales (which is how just car get their averages when agreeing on a value most times) I would be up for about $30-$34000.

that's not including on roads and my excess of about $1k. so lets say about $35,000.00

hows that for a jump in values. now im not looking at this as a wide eyed kid thinking my cars worth whats its not, im just looking at the averaged from available value. but im confident could get $30k for my car if sold today.

so, I have contacted my insurer who currently has a value in the low 20s with a $900 excess, that's just car. im now looking into what they can do with the agreed value, pointing them to do their own market research and with the explanation of the USAs influence on the import value and looking at what the limited insurance market can offer in competition.

also they have an agreed value as I said, but their market value is $17000 btw, probably relevant when I bought it but ... imagine trying to get a 32gtr for $17000 today, gumtree shitter maby....

My question...

what value do you have your GTR insured for?

im asking specifically for R32, but R33 and 34 are not about to start dropping any time soon.

are you insured for what it would costs you to replace or within reason? who did you use? ...discuss :)

ill post back my results to btw so others know what's available or at least realistsic, it would be good if we got some info on this for values, premiums are too hard cos everyone's situation is different but hopefully no one gets caught out and given a cheque for half their cars value when paying for an agreed amount they didn't research.

Edited by GH05T
Link to comment
https://www.sau.com.au/forums/topic/464155-r32-gtr-insurance-values/
Share on other sites

I'll play

R32 GTR insured value $40k

$500 excess

Would it replace what I have spent - NO.

Could I get $40k, at todays market value, likely be close to that.

Insured through Shannon's.

Comes out of the garage about 30-40 times a year.

I have started talking with shannons. They have a value off the bat up to 25000 atm. Keep in mind, mainly stock 89,

I am going to go through all the mods and see if i can push that up. The new haltech might add a grand.

Moved my 1990 GT-R to Shannons this month.

Spent about 30 mins on the phone with underwriter. Started at 21k. Went to 25k once he started looking at comparable cars on Carsales. He upped it to 30k when I explained the engine had been rebuilt etc. It seemed like a reasonable way to work through it.

Based on this, I will do some research leading up to renewal next year to see where prices are at.

30k would not come close to covering what I have spent buying and having built - that is a different story - but it is a lot closer to buying something comparable than I would have been previously.

The underwriter just glanced over mine briefly when I had in at the shop. Mines still running stock motor but I gave him a list of items I've got on it totaling more than what they're covering me minus the vehicle cost.

the difference in premium from 20k to 25k was about 120 bucks over the year. If i'm paying around 2k anyway, another 6% is worth the 5k extra coverage.

I upped mine to 22k from 18 about a year ago, If it were to get written off or stolen I wouldn't replace it, would be just glad to get back what i brought it for initially (18k 3 years ago) anything more than that would be a bonus and go towards the reimbursement for the 15 odd grand i have spent fixing everything.

Varies a lot. How many have actually been seen by an assessor and do they know what they're looking at?

Any vehicle with defects rendering the car unregisterable would the Insurance company not pay out?

I don't have any concerns but I bet the majority do. Lol

Edited by Sinista32

Mine did, I wasn't certain if they knew what they were looking at but did provide a list of parts that have gone on and the costs.

I think they were just making sure it wasn't some clapped out crapbox that wasn't worth what they were signing up for.

I should up it to $40k given that it won't replace it but get much closer than the current $25k

  • 2 weeks later...

Agreed value of $25k (1989 R32 GTR - rebuilt motor) - Shannon's. Going to speak to them soon and look at agreed value of $30k.......

As you've mentioned $25k wouldn't come close to replacing my car now......Thanks for the gentle reminder ;)

  • Like 1
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...