Jump to content
SAU Community

Shockworks Presents Round 9 - Sandown Raceway 1st Oct | Grand Final Day


Recommended Posts

Hey guys I have fixed the track day requirements link for anyone not sure what is required for a car and driver to attend.

 

http://www.sau.com.au/forums/topic/453779-track-day-requirements/

  • Like 1

Cams Manual Schedule D - Apparel

http://docs.cams.com.au/Manual/GeneralRequirements/GQ05-Schedule-D-2016-1.pdf

We're "Race" / "Multi Club"... So Helmet level is "B"...

In the table it seems to list "E22 (with 03, 04 or 05 amendments)" which looks like your helmet. But don't quote me on that, that table is confusing as hell.

  • Like 1

Ha ha yeah thanks for that@Odium i found that table super confusing too ! Just strange you dont need a as/nzs sticker on a road approved helmet

3 hours ago, OYEAHA said:

Ha ha yeah thanks for that@Odium i found that table super confusing too ! Just strange you dont need a as/nzs sticker on a road approved helmet

 

Sorry was busy earlier could not reply in length.

 

the ECE is accepted by vic roads as well now so it's not just CAMS that are accepting it.

 

so Snell, ECE, AS and BS we accept.

 

 

  • Like 1

Thanks Martin :)

Yep in my search for the answer I came across an article saying that they were road legal in Victoria since mid 2015, but still illegal if you travel to certain other states on your motorbike (ridiculous considering that you can be considered "Safe" in a $75 helmet, but not in a $750 helmet)

Thanks for the clarification

Hello :-)
I just bought a fire extinguisher, its a 1kg cams approved, the date on the neck is 03 2016. The lovely man at the shop assured me that it was the make date i just want to confirm. Is it valid 3yrs from that date? Im having trouble getting my head around whats an expiry date/make date. Any help would be appreciated. Tegan

that is correct 3 years from the date stamped on the bottle.

 

so good till march 2019

 

make sure it is bolted in, no cable ties/tech screws and such.

 

M

19 minutes ago, fdrx7 said:

Hello :-)
I just bought a fire extinguisher, its a 1kg cams approved, the date on the neck is 03 2016. The lovely man at the shop assured me that it was the make date i just want to confirm. Is it valid 3yrs from that date? Im having trouble getting my head around whats an expiry date/make date. Any help would be appreciated. Tegan

Yes that is correct. 3 years from manufacture date

Unless it specifically says "Expiry Date" then consider it a Manufacture date, as different uses have different time spans (for the same equipment)... Stupid I know.

  • Like 2
On 9/26/2016 at 10:35 PM, acsplit said:

I was just about to post this, yep contact brendan during office hours garage $50 can fit two cars

Damn that's cheap, PI was like 4 times that




  • Latest Posts

    • Messing around with. Twin kit for. Rb30/26  
    • For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
×
×
  • Create New...