Jump to content
SAU Community

Recommended Posts

Hey everyone I've recently built in RB30 26 in my R34 series 2 I'm running Evan's waterless coolant new technology my car sits at around 95 degrees wondering if this is a standard temp in comparison to standard coolant additives.16e301d34ef80ed723f53bf3c1d76420.jpg

Link to comment
https://www.sau.com.au/forums/topic/466858-evens-waterless-coolant/
Share on other sites

Never used evens waterless coolant but in theory shouldn't it run cooler? 95 degrees sounds hot for normal operating temp, my stockish rb25 sits around 82-83 operating temp with normal Nulon coolant and stock radiator.

though on the track my mates 25/30 sees 100+ regularly and nothing drastic has happened.

Just had a look through some of my logs.

Summer driving around without too much traffic sees anywhere from 70-85'C

Summer during stop start 80-92'C

Summer while setting up anti lag and launch control 85-93'C

Thermo fans, 42mm rad, Penrite coolant. Using the factory ecu temp sensor to adaptronic. Fmic. Fans turn on at 90'C and turn off at 86'C

 

I remember a mates NEO used to sit around 95'C during summer. The defi alarm would go off every now and then (100'C?). Stock rad, unknown coolant with a fmic.

 

How well calibrated is your coolant temp sensor @brodielezgt  

That seems like a very low temp for std rad @dyl33 

3 minutes ago, brodielezgt said:

When should I start getting worried.

I wouldn't be worried. Seems normal from what I've personally seen. And a quick skim through some old temp threads shows anywhere from 70'C-105'C to be normal. Obviously depending on your location and season.

 

Something to think about - With no fans and bonnet shut in the sun at idle, my temps seem to progressivly slow down once they get over 95'C. Takes roughly 10mins to get to 110'C

my mate ran this in his LS
temps improved 10-15C

but, he also had a leaking radiator repaired at the same time so i'm not sure if that had anything to do with the decrease in temps

not worth it i think. You wouldn't want a hose full of oil letting go on a high speed bend

plus, you have to completely remove all the water from your engine otherwise the product won't work properly (its best to use on a new engine that's never had water)

to completely dry out the water gallery's we removed the top and bottom radiator hose then connected a leaf blower into the top hose and let it blow into the engine for 10 minutes until there wasn't any more water coming out of the bottom hose


What did you  expect it to do? It is not designed to make your engine cooler it just has a higher boiling point than water...190 deg C if you believe the label. So water temp is not the concern - you should keep an eye on your oil temperature and pressure.

  • Like 1

Temps will be higher than water... for a perfectly working system.
Water has better heat capacty so will cool slightly better, until it boils. the point of this stuff is for bikes/crappy old cars etc where the cooling system is poor and you don't want it to boil even if it gets hot.
The racing coolant is the opposite, where you need maximum cooling (and also don't want to dump glycol on the track) and your cooling system is on point so its not going to get to a temp where it could boil.

 

Basically, best coolant is normal coolant.

  • Like 1

I ran this coolant in my RB26 after engine rebuild as heard promising results. Turned out to be quite expensive (compared to normal coolant) and as already said was really no different to normal coolant under normal driving conditions. I too expected it to run cooler but that is not what it's meant to do and just resists it more effectively. Didn't really get to test it properly under extreme conditions but had a few leaks and it smelt quite strange when spilt as well. When it leaks of course you must only top it up with more Evans coolant which is really quite difficult to find (had to buy mine through mail order) so if you are not carrying some with you and get a leak you are in allot of trouble... Ended up getting rid of it after not very long as it is just too expensive for not a great deal of benefit under normal driving conditions. More inconvenient to maintain for me and never had any problems with normal coolant anyway so just went back to that.

Im about to put in a new koyo radiator and during my research came across Red Line Water Wetter

The claims and reviews give it decent thumbs up, naturally I bought some as an option

Anyone able to vouch for it?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...