Jump to content
SAU Community

Recommended Posts

37 minutes ago, Dose Pipe Sutututu said:

That's how the NBN is being rolled out lol

lol no, the NBN is being rolled out equivalent to you just saying f**k it and using the cracked o-rings

 

48 minutes ago, Dose Pipe Sutututu said:

So close yet so far, typical NBNish delivery lol.. Over budget and project schedule blown out of the water.

This is EVERY Government funded project

  • Like 1
  • Haha 2
1 hour ago, iruvyouskyrine said:

Those bolts go at the very back of the head on either side. Do you even RB bro?

No :(

I SR20 more lol...

where exactly????

1 hour ago, Dose Pipe Sutututu said:

are those the cylinder head to block bolts that go on the outside??

That's what I thought they were when I saw the pic. I thought there was one front and one rear though not both at the same end?

1 hour ago, Dose Pipe Sutututu said:

are those the cylinder head to block bolts that go on the outside??

Yes correct. 2x M6 bolts

 

38 minutes ago, timmy_89 said:

That's what I thought they were when I saw the pic. I thought there was one front and one rear though not both at the same end?

1 at front intake side and 2 at rear either side.

I should note that i never put them back in any of my engines. With RB25's you can't access the front bolt without taking the inlet manifold off which is a shit job which annoys me as i would rather take the inlet manifold off when the head is out of the car.

15 minutes ago, iruvyouskyrine said:

I should note that i never put them back in any of my engines. With RB25's you can't access the front bolt without taking the inlet manifold off which is a shit job which annoys me as i would rather take the inlet manifold off when the head is out of the car.

Yea they didn't go back on my engine either lol

ahhh I installed coppery colours ones back into those holes.. interesting those bolts I took a photo of, I wouldn't' think they would fit as they're wider than the golden/copper ones I used from the R33 motor.

mad, no fear - didn't fk up

Update but no photos (taking inspiration from @luke gtr lol).

Removed R33 plenum, installed bottom half of R34 plenum.

Now awaiting 1550cc Bosch injectors and a Plazmaman rail. The initial plan was to use the 875cc Siemen DEKA V I had from my old motor but anticipating the power this motor will make there's no way those injectors would cut it, even if I ran 4 bar base pressure.

Been trying to order parts again from Andrew @kudos.motorsports but he isn't replying to my emails :(

 

Update but no photos (taking inspiration from [mention=37584]luke gtr[/mention] lol).
Removed R33 plenum, installed bottom half of R34 plenum.
Now awaiting 1550cc Bosch injectors and a Plazmaman rail. The initial plan was to use the 875cc Siemen DEKA V I had from my old motor but anticipating the power this motor will make there's no way those injectors would cut it, even if I ran 4 bar base pressure.
Been trying to order parts again from Andrew [mention=1172]kudos.motorsports[/mention] but he isn't replying to my emails [emoji20]
 
Nawww, thanks brosef.
1 hour ago, ActionDan said:

Side feed in that boat anchor engine aren't they? 

yeah nah cuz.. I had top feeds in there under the stock plenum before they were even mainstream :)

http://www.trak-life.com/diy-converting-top-feed-injectors-r33-gts-t-skyline-rb25det/

Yah... stainless internals, not modified by any laser cutter/mill/bench grinder/side cutters

US guys usually refer to them as Siemens DEKA V 80lb

I hate modified injectors, those "Bosch 1250cc" are milled.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • This is aem disk setting in aem tuner and still 180 dgree off or ignition on exhaust cycle is it from cas it self as cas seems wouldn’t fit in cam shaft if wrong position and wiring been verified any ideas 
    • Oh yeah that would work excellent. Should be the same diff housing & everything. Shoot me a text or call me 260-750-2246 -Cody 
    • Oh right, I didn't realise it was your car. Please do! Makes me feel better about mine. I also have a big scrape on the front left bumper where someone presumably used the wall to guide the car into a parking spot  But somehow all the funds go towards mechanical things and the cosmetics stay forever unfinished... Interesting, I don't think I have seen it before. But after seeing @PranK's rusty roofline on the BMW I'd probably leave it alone. Wouldn't want water to get in there.
    • Thanks mate, thought you might know the answer.     
    • Infiniti US are teasing a manual Q50 as a way to refresh a (very old) model. https://torquecafe.com/manual-performance-sedans-arent-dead-yet/ Can't be too technically difficult given the Z has the same motor with a manual gearbox......here's hoping there is a JDM version we can import here, that would save me a world of headaches
×
×
  • Create New...