Jump to content
SAU Community

Recommended Posts

Shit Box Specs:

  • Garrett GTX3576R Gen 2, divided 1.01
  • Tomei 260/9.15mm Poocams
  • Sinco Twinscroll manifold, single gate (pulses split all the way to the gate)
  • Turbosmart Gen V 50mm Gate
  • 3.5" TBE with 5" 100 cell cat, mid muffler and rear muffler
    • Gate plumbed in after cat
  • Built blah blah.

 

I think the power range I guess will be fine then? 

Or should I bump the range to 440rwkw to be safe? 

Close to 600rwhp seems about right? 

Edited by ActionDan
1 hour ago, Dose Pipe Sutututu said:

Shit Box Specs:

  • Garrett GTX3576R Gen 2, divided 1.01
  • Tomei 260/9.15mm Poocams
  • Sinco Twinscroll manifold, single gate (pulses split all the way to the gate)
  • Turbosmart Gen V 50mm Gate
  • 3.5" TBE with 5" 100 cell cat, mid muffler and rear muffler
    • Gate plumbed in after cat
  • Built blah blah.

 

Are you going to fully send it ? What kind of Dyno?  And fuel system big enough to support full send (thinking 1300cc injectors?)

Edited by Lithium

@LithiumMainline roller dyno, will be using 255 semi slicks too LOL.. don't have any other tyres/wheels to use.

Fuel system will be good :)

  • Bosch 1480cc (aka 1500 or 1550 or 1650cc depending who you talk to)
  • 2x Walbro 460L in surge
  • 1x DW200 in tank (lift)
  • 8AN from surge to rail
  • OEM feed & return as return

Not too sure about full send, however let's see. A bit scared the gearbox will go bang instead lol.

  • Like 1
1 minute ago, admS15 said:

452kw and an exploded gearbox within 2 hours of finished dyno session.

LOL as I was typing the above response about gearbox going ka-blam lol

1 minute ago, Dose Pipe Sutututu said:

LOL as I was typing the above response about gearbox going ka-blam lol

Just stay out of 3rd gear, she'll be right. Otherwise, i have a brand spanking new in box r34gtt gearbox sitting in my shed that may or may not be for sale. Actually, i better hold onto it.

1 minute ago, Dose Pipe Sutututu said:

@LithiumMainline roller dyno, will be using 255 semi slicks too LOL.. don't have any other tyres/wheels to use.

Fuel system will be good :)

  • Bosch 1480cc (aka 1500 or 1550 or 1650cc depending who you talk to)
  • 2x Walbro 460L in surge
  • 1x DW200 in tank (lift)
  • 8AN from surge to rail
  • OEM feed & return as return

Not too sure about full send, however let's see. A bit scared the gearbox will go bang instead lol.

That should be a very solid setup all around if it all cooperates and you aren't shy.   I'll go with 452kw but more or less wouldn't shock me 

@admS15 will need to, will find a pair before the dyno day.

@Lithium kind of pulling my finger out because I have a track day to attend (gift from the S15 owner I tuned recently).

1 minute ago, ActionDan said:

Just saw your fuel system, downgraded power now because using pleb brands.

I know, at least 50kW less now because not ID injectors and mechanical pump.

On 5/30/2020 at 4:13 PM, Dose Pipe Sutututu said:

Why not, celebrate driving the R33? Great excuse to open it.

20200530_160734.thumb.jpg.c65a957f1c1f4afc476ca298261a898e.jpg

We are coffee pals. I have the same machine (well actually the cheaper one without an LCD). 
Mine has been going strong for 5 years. It's been through three offices and now makes my morning coffee without fail.

Literally the greatest little coffee machine i could have asked for. I trust yours is going just as strong?

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...