Jump to content
SAU Community

Recommended Posts

1 hour ago, GTSBoy said:

......By contrast, Sydney had it so good with water that original fell on pristine mountainsides that their water supply engineers never learnt how to scrub water properly and so for years and years there were Giardia outbreaks and the like, that only stopped when some E&WS engineers went across and taught them how to do it.....

our Wombats and Kangaroos wee in that river.

  • Haha 4

So I decided that I wasn't happy with how I originally wrapped the loom with fleece tape. I didn't factor in the new intake manifold/plenum so it always sat a bit funny.

Yep, I decided to unwrap it and redo how the wires would branch out. Added in a light twist too, here's hoping I didn't snap any 30 year old wiring because FML if I did.

PXL_20240726_063235339.thumb.jpg.8084f7fc864a17b8f20e62b21d770978.jpg

Took a few more photos of the shit box too, needed it for Enthusiast Insurance as they wanted photos to justify why my agreed value was above market by a fair amount.

PXL_20240726_063313986.thumb.jpg.c4bb286a8d69f20dbb121e064d972121.jpg

PXL_20240726_063016998.thumb.jpg.996df36e205ffd88e2baa50b6564cde8.jpg

  • Like 7
  • 2 weeks later...

Somehow I managed to snap off the coolant sensor wiring when I pulled through the loom, then at the same time managed to also snap off the coolant dash sensor plug too.

To make things even more fun, I thought it would be nice to recrimp the ring terminals for the earths, to only find out the terminals I had at home were too small for a M6 bolt to go through. 

Anyhow, managed to fixed the lot yesterday during lunch, installed the e-throttle. Slow and steady, but we are getting there.

Next is to tidy up the harness with some trusty race zip ties and then install the starter.

PXL_20240809_065753363.thumb.jpg.861cc4fec5329d168fe402b870c4357d.jpg

  • Like 8

Pissed off the random Raceworks fitting on my car, was fitting when the new motor went on. 

Not sure what happened to the original Speedflow one before the motor went bang.

PXL_20240817_050024925.thumb.jpg.d58e8f0f01ec8f8c93e76a89da7c667b.jpg

 

Doesn't look like the catch can fittings are going to be very fun with the throttle body (and pipe).
Are they on different planes?

2 hours ago, Dose Pipe Sutututu said:

@Kinkstaah

And yes, the exhaust is so quiet you just hear plenty of injector noise and solid lifter noise.

Oh you sweet summer child. This is a quiet engine bay and a booming exhaust where I'm from lol. Sometimes I do miss the RB.

  • 1 month later...

Not much car shit happening as of late, been so busy with work and decided to also study to do a massive career backflip.

So yeah, working 2 jobs, means no time for Dose Pipe plays with toys time.

Anyhow, new Philips XL Air Fryer came today. Went for the non Wi-Fi version which is like $50 cheaper.

New air fryer, who dis?

PXL_20241013_095612088.thumb.jpg.437bc57ac4ef2dbb9bc59d03d99a10e2.jpg

  • Like 1
  • Haha 1
8 minutes ago, MBS206 said:

What're you studying to backflip yourself towards?

Finished studying already, mortgage broking 😊

Started working already too, have settled a handful of refinances and learning the ropes. All have been simple PAYG clients (all family and friends, can't thank them enough, trusting me with their finances).

Will say goodbye to the IT world for good one day, nearly 2 decades of ups and mainly downs lol... I'm burnt out from corporate, constant moving targets, constant scope creep, never a fking clear definition of an end goal.

Hope I've made the right move, if not, I hear job seeker allowances aren't too bad LOL.

  • Like 4

Do conveyancing, I cannot be arsed trying to actually buy a house and do all the legal stuff you need to do to purchase myself

I pay cash now, you make happen.....

  • Like 1

Might be an option when the business grows, never too late to teach an old dog new tricks.

Mid life crisis dis dat, also means moving forward I won't be too inclined to buying our future house anywhere near the CBD or Metro Sydney.

Come at me man shed and hoist and motion racing SIM and maybe a dyno? Lol.

Dyno Tune your Car and Home Loan.

  • Like 2
On 13/10/2024 at 9:42 PM, Dose Pipe Sutututu said:

Not much car shit happening as of late, been so busy with work and decided to also study to do a massive career backflip.

So yeah, working 2 jobs, means no time for Dose Pipe plays with toys time.

Anyhow, new Philips XL Air Fryer came today. Went for the non Wi-Fi version which is like $50 cheaper.

New air fryer, who dis?

PXL_20241013_095612088.thumb.jpg.437bc57ac4ef2dbb9bc59d03d99a10e2.jpg

wait till you discover scented fabric softener, EVERYTHING SMELLS LIKE VANILLA NOW

  • Haha 1
On 10/13/2024 at 8:54 PM, Dose Pipe Sutututu said:

Finished studying already, mortgage broking 😊

Started working already too, have settled a handful of refinances and learning the ropes. All have been simple PAYG clients (all family and friends, can't thank them enough, trusting me with their finances).

Will say goodbye to the IT world for good one day, nearly 2 decades of ups and mainly downs lol... I'm burnt out from corporate, constant moving targets, constant scope creep, never a fking clear definition of an end goal.

Hope I've made the right move, if not, I hear job seeker allowances aren't too bad LOL.

What's your best deal to refinance my mortgage? 😛

I just want to be paying the banks the least in interest, so no fees, low interest, and either redraw available or 100% offset accounts...

24 minutes ago, MBS206 said:

What's your best deal to refinance my mortgage? 😛

I just want to be paying the banks the least in interest, so no fees, low interest, and either redraw available or 100% offset accounts...

Depends on your LVR and also loan size :)

Happy to help out, flick me a PM with an email or mobile

3 hours ago, Mohsen said:

do you want to occasionally come back to the IT world and do CSVs for me? i pay

CSV? Come on lad, I'm all about PowerBI these days.

I would consider working as a PowerBI or ZOHO DataPrep consultant, but nah, I've had enough of IT. Two decades of being in somewhat in an industry I kind of just chose because I had zero guidance when I was younger.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...