Jump to content
SAU Community

Recommended Posts

Leaving your car in reverse gear while rolling down a hill

Hey guys,

Earlier today i turned into a steep hill street and I realised that it was the wrong street so I put it in reverse gear to pull out of the street but then a taxi came up behind me so I couldn't get out of the street. So I went down the hill but after going down about 50 metres I realised I still left it in reverse gear while my foot was pressed down on the clutch pedal. I only realised I left it in reverse gear when I heard that winding noise reverse gear makes so I immediately put it in neutral. 

I was wondering if this could damage the gearbox or any transmission system or anything else on the car. I tested reverse gear straight after and it still seemed fine but I just wanted to make sure.

thanks

Edited by IM-32-FK
I'm sure 50m won't cause a problem, but potential issue is that the oil pump is running backwards so no oil pressure in the motor for that time. 
 

Seen as his foot was on the clutch and im guessing the car must have been running (seen as it was being driven prior to this) for a start would not have been an issue.
  • Like 1

 

1 hour ago, Duncan said:

I'm sure 50m won't cause a problem, but potential issue is that the oil pump is running backwards so no oil pressure in the motor for that time. 

 

I'd like to here your reasoning for this Duncan....how does the oil pump run backwards?  This  - to my thinking - means that the motor was running backwards??

Only way I can think of this happening is if you are rolling backwards down a steep hill while its in say 3rd gear but the motor is switched off??? And if its switched off, no bang or boost so no oil pressure would not be a bad thing given the duration. But willing to learn.

1 hour ago, tridentt150v said:

Nope, not a thing.

Sorry forgot to mention that the front of the car was facing down the hill . I wasn't going down the hill backwards like I was reversing down the hill if u can get the picture

8 hours ago, Duncan said:

I'm sure 50m won't cause a problem, but potential issue is that the oil pump is running backwards so no oil pressure in the motor for that time. 

 

Haha, The engine runs clockwise no matter what gear you are in... Oil pressure would not be effected at all.

If you had of taking your foot off the clutch then best case scenario the engine stalls and you come to a abrupt stop... worst case something may have broken from the shock load..

But you didn't so nothing to worry about at all.

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...