Jump to content
SAU Community

Recommended Posts

1 hour ago, ActionDan said:

Well seems my car is about on par with what everyone else is seeing so fair enough. Will just have to run 98 for the longer cruises. 

I'll just have to put a big fuel cell in the boot for some extra capacity lol

I used 50L on Saturday on 98 (150kms)....

Used a lot of 3rd gear (5-6K rpm up and over the hill and back)...

1 minute ago, ActionDan said:

Really? that's way more than I expected? That would be about what I used? 

Yep - I filled it with Shell 98 on the way out  and less than 1/8th of a tank left.  Haven't refilled to verify- but given it takes a bit over 60L - 50L is what I would expect.

I was probably working harder in the rev range to keep up....

My 25det neo with ~380 kw to wheel

Driving from perth to albany, i got about 450 km to a tank, on the light, maybe could have squeezed another 10 or so ks out of it.

No narrowband or wideband hooked into ecu/tune.

I think thats pretty good haha.

Bigger turbo with generally softer response sub 3000rpm and less restrictive turbine can all contribute to fairly respectable fuel consumption in those conditions, for sure.  I agree with Jared, pretty good result when you think what it does when the taps are opened.

4 hours ago, jay-rod said:

My 25det neo with ~380 kw to wheel

Driving from perth to albany, i got about 450 km to a tank, on the light, maybe could have squeezed another 10 or so ks out of it.

No narrowband or wideband hooked into ecu/tune.

I think thats pretty good haha.

was suprised to see Albany had E85. was expecting you guys to bring 20 jerry can each but was suprisingly few there.Now just need it in Bunbury!!

15 minutes ago, ActionDan said:

Interesting. I've just been putting straight United Race Blend in it, though I notice the sensor never reads above 80% despite my testing showing 90+ with the basic water/shake in tube tester. 

Same, sensor tends to read around 79-80% (genuine gm continental). Only ever diluted it with 98 once, took ages to get back up to 79-80%

Yeah, if you run flex then it's really hard to get up to >80% if you aren't using straight ethanol - which means that it's also not too hard to keep it floating around 50-60% if you occasionally top up with a bit of petrol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...