Jump to content
SAU Community

Recommended Posts

8 hours ago, Kraaken.r32 said:

Hi guys, been reading up on this as I have now bought some of these echo coil packs. I want to do this swap in mt rb20. Do I bypass the ignitor? If so how can this be done? Also is the wiring for the coils the same as rb25? 

Yes you have to bypass the igniter. It’s done by bypassing it 

Just now, Ben C34 said:

Yes you have to bypass the igniter. It’s done by bypassing it 

ok great, is it a direct wire to wire? i cant find any info on that, do you normally just splice togther? if you know which wires need spliced would be great info for the thread

Hi Kraken,

I just completed this not to long ago on my RB20, what I did was identify what wire from the ECU fired what cylinder and then soldered that wire up to the corresponding plug on the loom. Another way to do this is outlined above by just pairing the numbers on the bottom of the ignition coil. But I recall there was an extra wire I had to do something with, I'm pretty sure it was a ground wire which I just paired up with the other ground wire that goes onto the coil pack holder..

Below is the colour combination of the wires for my stock ECU which may be relevant but double check yours.. 

54236697_2526481310712901_1661104337172037632_n.jpg.32e6bcde421a9886c06f9405e457e3ac.jpg

11 hours ago, Dylannn said:

Hi Kraken,

I just completed this not to long ago on my RB20, what I did was identify what wire from the ECU fired what cylinder and then soldered that wire up to the corresponding plug on the loom. Another way to do this is outlined above by just pairing the numbers on the bottom of the ignition coil. But I recall there was an extra wire I had to do something with, I'm pretty sure it was a ground wire which I just paired up with the other ground wire that goes onto the coil pack holder..

Below is the colour combination of the wires for my stock ECU which may be relevant but double check yours.. 

54236697_2526481310712901_1661104337172037632_n.jpg.32e6bcde421a9886c06f9405e457e3ac.jpg

Thank you very much that makes sense! Thank for the pinout will help with future guys doing the swap as well as my self! 

 

14 hours ago, GTSBoy said:

The wire that goes to the igniter for coil 1, now needs to go straight to coil 1.  I think you can work the rest of the pattern out.

Yes great answered many questions with that. 

  • 2 weeks later...
  • 1 year later...
  • 1 year later...
  • 1 month later...
On 10/10/2021 at 6:04 AM, ganthercage said:

It is hard to beat RockAuto for these, at least for quality coils -- Denso, NGK, AC Delco/Delphi. Avoid junk. Denso is a major supplier to Toyota, and Toyota had a lot to do with getting the company off the ground and is still a big minority owner.

If DENSO makes the part then it's the OEM Toyota part - so buying it from a Toyota dealer is just a DENSO part in a Toyota box with mark up. 

 

Any reason people are not running R35 Coils? They are generally considered best on the market and only cost $60/ea. 

Yaris DENSO 6731306 - $52/ea

R35 Hitachi IGC0079 - $61/ea

 

PRP has a breakdown of the two coils in comparison. 

 

https://platinumracingproducts.com/pages/r35-coil-vs-yaris-coil-debate

 

 

On 12/1/2021 at 2:57 PM, GTSBoy said:

People are using R35 coils. No-one in their right mind would choose Yaris/Corolla type coils. This thread is a hangover.

If we're going to revive a thread like this we should discuss the recent drama around this article: https://www.50ignite.com/blog/technical-blog/article-3-back-to-back-testing-of-370z-coils-re-co

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...