Jump to content
SAU Community

Brendons M35 build

Sack87

By Sack87,
in Four Door Family & Wagoneers

 Share

Recommended Posts

  • Replies 174
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Sack87
Sack87

Brendons M35 build Thought I'd create a mini build thread on my progress with my first foray into Nissan wagon life and also a place to ask questions/path to follow. I bought the car with f*

Sack87
Sack87

And you know everything I assume, including how to hack and tune a factory Ecu? Firstly I'm running a Billet Intense RS Turbo and secondly it's safe on 19psi as my AFR doesn't go above. 93v at WO

Sack87
Sack87

Pulled out the nav unit to make way for the EMU. Made up a bracket/fascia to house it and have two provisions for the option harnesses. I still need to wire in the LC2 and mount the unit but that can

Posted Images

  • 2 weeks later...
sta934 Rookie

sta934

Posted
Posted
Yeah same for mains. 
You can buy single pistons from Nissan, which I did to replace number 6 and bought another set of rings. All the bores got honed so it's fresh again.
They're both headache savers but Amamaya's processing time is a bit slow. Everything is in Australia for this order yet it takes 3 weeks to get it.

Hey mate, was just wondering what grade bearings came out of your engine?, connecting rods and mains. I had grade 0 across the board. I was expecting to see graded bearings in there to match the blocks crank bore and crank journal and pin journal size stampings. Did you just replace with same grade bearings that came out or get the micrometers on it? Cheers
Sack87 Community Regular

Sack87

Posted
  • Author
Posted
On 10/07/2019 at 1:01 PM, sta934 said:


Hey mate, was just wondering what grade bearings came out of your engine?, connecting rods and mains. I had grade 0 across the board. I was expecting to see graded bearings in there to match the blocks crank bore and crank journal and pin journal size stampings. Did you just replace with same grade bearings that came out or get the micrometers on it? Cheers

Pretty sure mine were grade 0 too. I just put what came out back in and all the clearances came up spot on.

  • Like 1
Sack87 Community Regular

Sack87

Posted
  • Author
Posted

Finished off Deutsch plugging the engine harness. If I decide to change ECUs down the track, all I have to do is Deutsch plug that harness.

It turned out bulkier than I would have liked but it will be tucked away behind the glove box.

IMG_20190714_185758.jpg

IMG_20190714_185932.jpg

  • Like 2
andynogo Collaborator

andynogo

Posted
Posted

Oooh 3k! Should be interesting to see what the normal driving is like. Should be pretty ors for the drag strip! They've got expensive though ... Must be a long time since I've checked the prices! Sigh. Another thing to add to the budget... :)

Sack87 Community Regular

Sack87

Posted
  • Author
Posted

Pulled out the nav unit to make way for the EMU. Made up a bracket/fascia to house it and have two provisions for the option harnesses. I still need to wire in the LC2 and mount the unit but that can be done after run in.

IMG_20190726_173649.jpg

  • Like 7
  • 4 weeks later...
Sack87 Community Regular

Sack87

Posted
  • Author
Posted

Fitted a Raceworks 340lph fuel pump and wired it with direct 12v feed. You can't even hear the thing ?

FYI, on M35 Facebook book page and Matt's photos, there must be a slight change to the pump since 2016 as it didn't go all the way into the filter. With all my body weight on it and with silicone spray, that is as far as it would go in. Can't run the rubber damper as it would not ever fit. It's not coming though as I modified the base so it cups the end of the pump.

(I did have the base on the wrong way in the pic!)

IMG_20190817_163047.jpg

IMG_20190817_163059.jpg

  • 2 weeks later...
  • 3 weeks later...
Sack87 Community Regular

Sack87

Posted
  • Author
Posted

Got the turbo back and they said they found nothing. They said it was either too much oil supply or not draining enough.

I asked what pressure they test them to and they said their machine does 60psi max. When I said these engine do up to 120psi and I had drilled the restrictor out, he said that will will most definitely make it leak as its way too much for even the wider seal they put in there to handle it.

Burred out my drain as big as I could and under their advice, bought a Turbosmart Oil Pressure Regulator (OPR) These are made to only allow 40spi into the core but at maximum flow.

Only place it could go is in the cam cover as it needs a drain. Drilled a hole just below the filler and inserted a tight fitting grommet. Ran new lines and it seems to be all sweet for now.

IMG_20190914_130153.jpg

IMG_20190914_165446.jpg

  • Like 2
  • 1 month later...
Sack87 Community Regular

Sack87

Posted
  • Author
Posted

Got around to welding in another muffler, 100 cell cat and O2 bung.

Car did not get any quieter which I had hoped for because I have another piece to weld on when I get it to make it louder!

IMG_20191104_125724.jpg

IMG_20191104_125915.jpg

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Lock up the old for sale / wtb threads.

      By PranK · Posted

      We have a huge update coming in the next few months, version 5 of Invision will be released. I'm holding off any changes until after this change as I'm not sure what features will be removed or introduced.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Duncan
      NC MX5

      By Duncan · Posted

      Quite right, if you make it to that pension you deserve every cent
    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
×
×
  • Create New...