Jump to content
SAU Community

Recommended Posts

Not sure what Pete does but I hadn't planned on it. You would run a cooler on the return line if you wanted, or just some extra length of line and loop it to increase the length of hose used which will help cooling a little

1 minute ago, ActionDan said:

I've thought about elec steering before. 

What's your main reason for the conversion? I have seen RB PS pumps split apart at track days, is that he reason or less parasitic loss? 

 

 

Na I am sure it does help there but f**k all really

 

main reason is the removal of stupid lines up front

renkves the pump 

high pressure lines to rack that all run under and over the crossmember and then the Lo pressure line that does a loop and head forward to the cooler

so it frees up space up front removes the weight to the rear and allows you to run a inline cooler under the car which helps with cooling up front

makes mounting a high mount turbo easier with now resivour up front as well

IMG_6880.thumb.JPG.ee5806ab85ce0ed15d101e124d89ff7c.JPGIMG_6881.thumb.JPG.9d96e6c1f19249212d58cd5bcf936ce2.JPGIMG_6882.thumb.JPG.3550c4eec0086f3e4ef237e36f9e076e.JPG

The rack lines are at the rear as well so will make getting that top starter bolt heaps easier too

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...