Jump to content
SAU Community

Recommended Posts

Hi All, 

Just wanted to get every ones advice on a couple of things. currently upgrading the whole fuel system. fuel system will consist of 8an feed and return, turbosmart fpr2000, raceworks surge tank  with x2 walbro 460s and 1 walbro 460 in the tank. 

my question is, from the tank to the surge, im planning to use a push on 5/16 to 6an fitting to get from the tank to the Supply of the surge. is this large enough? if not how should i configure it.

Also, regarding the flex sensor which is to go in the return line. the return will be 8an, is the flex sensor in line going to be a 'bottle neck'?

car; r32 gtr if it makes a difference. 

looking forward to hearing feedback, thanks. 

Link to comment
https://www.sau.com.au/forums/topic/472753-upgraded-fuel-system-questions/
Share on other sites

Sounds like you are pretty much on the money mate. 

Yes you are also right that the flex sensor will become a restriction on the return line. The answer to that is simple just run a bypass. So a tee either side of the flex sensor as the sensor itself requires bugger all flow to read the content levels. 

Also dont forget to upgrade your tank breather line on your fuel hat! Run with something big like a -12 as now you're gunna have 3× 460 pumps trying to suck  the tank inside out. Often over looked but as soon as that tank starts coming into "vacuum" you will start to have fuel supply issues. So keep your tank at atmosperic pressure and those 3 pumps will be able to drink all they need ?

Edited by Mick_o
  • Like 1

I would run a smaller lift pump, even a Wallahbro 255 or smalelr wherever to possible to reduce the heat production.. flex sensor, would just install it on the return between the surge & fuel tank :)

  • Like 1
1 hour ago, Dose Pipe Sutututu said:

I would run a smaller lift pump, even a Wallahbro 255 or smalelr wherever to possible to reduce the heat production.. flex sensor, would just install it on the return between the surge & fuel tank :)

Still has to be large enough to keep up with the demands of the twin feed pumps at full song draining the surge tank.

  • Like 1
7 minutes ago, Piggaz said:

Still has to be large enough to keep up with the demands of the twin feed pumps at full song draining the surge tank.

Correct but under less fuel pressure (pretty much 0.1bar) the Wallahbro 255 lift pump would perform about the same as say a single 460 Wallahbro at 5 bar (factoring in on boost on noise).

I don't have graphs as I'm on my phone.

  • Like 1
On 23/11/2017 at 3:45 PM, Mick_o said:

Sounds like you are pretty much on the money mate. 

Yes you are also right that the flex sensor will become a restriction on the return line. The answer to that is simple just run a bypass. So a tee either side of the flex sensor as the sensor itself requires bugger all flow to read the content levels. 

Also dont forget to upgrade your tank breather line on your fuel hat! Run with something big like a -12 as now you're gunna have 3× 460 pumps trying to suck  the tank inside out. Often over looked but as soon as that tank starts coming into "vacuum" you will start to have fuel supply issues. So keep your tank at atmosperic pressure and those 3 pumps will be able to drink all they need ?

Thanks. General consensus seems to be bypass. 

If i was to use a large breather how would i configure it? Delete/block stock breather and fit an aftermarket bypass near the top of the filler neck?

3 hours ago, Dose Pipe Sutututu said:

I would run a smaller lift pump, even a Wallahbro 255 or smalelr wherever to possible to reduce the heat production.. flex sensor, would just install it on the return between the surge & fuel tank :)

Long time ago it was just suppose to be a pump upgrade and shit.... yadda yadda yadda here we are. 

 

2 hours ago, Piggaz said:

Still has to be large enough to keep up with the demands of the twin feed pumps at full song draining the surge tank.

I do agree with this though. Id like to retain the factory fuel hat as it has the stock fuel sender. Hence my question about a 6an supply from the tank to the surge being sufficient. Of all the fittings i know of a 5/16 push on to 8an doesnt exist. 

Being a R32 GTR I would run one from the tank to the surge as those tanks are metal.

Then one filter out of the pumps to the rail. This keeps the surge tank clean and happy and the injectors happy.

Size wise ask @Piggaz, he knows more about filtration than a Russian rocket scientist LOL

  • Like 1

32 GTR is plastic tank, all other models metal tank.

Please sort it your wiring to all those pumps and make sure it is capable. 3 Walbros will be a hell of a lot of current (even though 1 is a lift pump)

  • Like 1
1 hour ago, iruvyouskyrine said:

32 GTR is plastic tank, all other models metal tank.

Please sort it your wiring to all those pumps and make sure it is capable. 3 Walbros will be a hell of a lot of current (even though 1 is a lift pump)

Yes wiring is sorted and wont be a problem.

1 hour ago, Mick_o said:

Good advice! ^^^ 

Also upgrade your alternator so it has enough beans to power them also! 

 

Was thinking to see how it goes, if the alternator doesnt like then look at an ARD one.

1 minute ago, WantGTR said:

Yes wiring is sorted and wont be a problem.

Was thinking to see how it goes, if the alternator doesnt like then look at an ARD one.

Spend the $$$ now mate and save yourself the grief of having issues on the dyno. 

That way you aren't paying your tuner to troubleshoot problems and you reduce your chance of starving your engine of fuel and hurting it.  Which is cheaper in the long run because lets face it you're putting alot of extra load on an alternator thats almost 3 decades old. So why put off the inevitable now and potentially risk your motor? 

  • Like 1

Ahh the old stock alternator with close to an extra 40 amps worth of load in feed pumps. They only produce 80 amp at full tilt. Just do it now!

Power, power, power. More, more, more. Where is it all coming from? ?

  • Like 1
2 minutes ago, Piggaz said:

Ahh the old stock alternator with close to an extra 40 amps worth of load in feed pumps. They only produce 80 amp at full tilt. Just do it now!

Power, power, power. More, more, more. Where is it all coming from? ?

coming from my wallet it seems haha

And then when you upgrade your alternator, I'll bet my left nut your voltage at the pumps rise. So now the pumps are singing along a bit quicker, flowing more... AFR's get rich... tune is out. Let's go for another excursion to the dyno.

What you tried to save, you bought anyway THEN add in another dyno session and the heartache of it all.

 

  • Like 1
27 minutes ago, Piggaz said:

And then when you upgrade your alternator, I'll bet my left nut your voltage at the pumps rise. So now the pumps are singing along a bit quicker, flowing more... AFR's get rich... tune is out. Let's go for another excursion to the dyno.

What you tried to save, you bought anyway THEN add in another dyno session and the heartache of it all.

 

 

49 minutes ago, Mick_o said:

Spend the $$$ now mate and save yourself the grief of having issues on the dyno. 

That way you aren't paying your tuner to troubleshoot problems and you reduce your chance of starving your engine of fuel and hurting it.  Which is cheaper in the long run because lets face it you're putting alot of extra load on an alternator thats almost 3 decades old. So why put off the inevitable now and potentially risk your motor? 

you bastards lol, i was 50/50 about this, knowing full well about the possible scenarios if i didnt upgrade. in anycase, RHDJapan will be getting yet another order from me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...