Jump to content
SAU Community

R34 GTT coupe - Rolling shell/ project

webber
 Share

Recommended Posts

webber Proficient

webber

Posted
Posted

I have an R34GTT project that I brought many years ago.  Has original Rb25det engine and manual gearbox with HD clutch to go with it. Car had been modified and previous owner stripped aftermarket turbo and performance parts to sell car and never put back together. So engine needs stock injectors and turbo put back on (pretty sure I have all of this)  and engine and box put back into car.  Pretty sure almost everything is complete to reassemble, clean mostly complete interior car had 145,000km at the time it was taken off the road.  Needs front and rear bars painted(lower Altia kit) ,  has been stored for at least 6 years that I have owned.  Fully complied and clear title.  Being sold as Is where is.  Will be getting some pics in the next few days. From memory it had tanabe coil overs,  nismo sway bars and a few other bits and pieces that I would have forget about. Probably missing a few bits and bobs from being stored in pieces for so long. 

Want $7K on Stockies or $8k with a set of genuine 19" volk CE28 19" gold rims

but open to offers.

 car is located in Deniliqun NSW 3hrs from Melbourne,  7.5hours from Sydney,  6hours from Adelaide. 

Strictly pick up only, no delivery. Not interested in organising freight as parts are bulky. 

Judging by recent 34 prices if someone is prepared to put in the work could end up with a nice cheap genuine turbo manual GTT

These will be the next generation of collectable car like the genuine mx7 plated vl Calais turbo

I don't come on here much but pm me I'll check it over the next few weeks

Link to comment
https://www.sau.com.au/forums/topic/473559-r34-gtt-coupe-rolling-shell-project/
Share on other sites
  • 1 month later...
  • 3 months later...
  • 2 months later...
  • 1 year later...
  • 3 years later...
Kinkstaah Grand Master

Kinkstaah

Posted
Posted

I think you'll find that the cost of this bare shell would have gone up considerably since then, so be mindful if anyone bumps this thread to not entertain the absolute steal that a 8K 34 GTT coupe shell would be (and was, back then)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • Kinkstaah
      Unpeeling the Orange

      By Kinkstaah · Posted

      The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • MBS206
      What brakes on R34 GTT(Europe)

      By MBS206 · Posted

      For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...