Jump to content
SAU Community

Recommended Posts

Hey guys, it's probably been covered, but for the life of me can't seem to figure it out and google isn't really helping.

The car will start fine and run fine, but after 5 minutes the whole car will seemingly die and the battery light comes on, its a new battery but has been charged and I didn't have this problem before, but however when the car has had that hickup it seems to be fine afterwards, just find it weird that i lose all power and engine cuts out, could it be alternator and or blown fuse causing the car to be shitty?

(Also this only happens first thing in the morning, in the afternoon on the way from work it has no problems at all)

Any advice is much appreciated :) 

Link to comment
https://www.sau.com.au/forums/topic/473759-r33-randomly-dies/
Share on other sites

11 minutes ago, r34.rory said:

Check the alt belt, could be worn and slipping or not enough tension maybe.

My R34 battery light came on last year and died turned out the belt for alternator shredded and flew off.

f**k,I'll have a look, i know my battery went dead a month ago but fully charged it and didn't have an issue till now, will check when i get home

Look, if the engine is just stopping, then either it has a mechanical problem / vacuum leak / fuel supply issue etc etc, OR it is simply losing electrical power to something vital.  These vital things include the coils, for example, and the ECU.  The Nissan engine management system is known by their abbreviation ECCS.  The ECCS relay is the relay that provides power to the ECU.  Its operation is a little complicated, but the overall view is that when you want the engine to be running the ECCS relay needs to be powered up.  Like all relays, they can get flaky.  When they do, they can drop power to the ECU, which tends to have sudden consequences.

You can find the relay near the ECU.  If you don't know what you're doing, you shouldn't stuff around down there, because you can make things worse.  If you had put the words "ECCS relay" into google, you would have found all the thousands of words that have been written on here across the last 25 years, in which you will find much wisdom.  The O2 sensor and the TPS are not likely to be responsible for your stoppages.  The CAS might.  The fuel pump might, just.  A broken wire in a loom definitely could.

Then it's not your alternator. If a dead alternator caused the engine to stop then the battery power would be drained. You wouldn't be able to start it back up.

GTSBoy noted many things to check. Start there as I reckon he's on the money.

As a side, I had a similar issue with intermittent stalling out of nowhere. After some trial and error I narrowed it down to my fuel pump relay - it's rare for these to die but it happens. I replaced mine and I was sweet, no more problems.

  • 3 weeks later...

Hey mate! Cleaned the iacv, also had a small vac leak on the std intercooler piping, but other than that it still struggles some mornings and still feels like it wants to stall, but I couldn’t find anything wrong in the wiring, even my mechanic couldn’t find anything. 

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...