Jump to content
SAU Community

V35 rb26 conversion

Ali
 Share

Recommended Posts

Ali Rookie

Ali

Posted
Posted

Hey fellas,

Just recently joined on this, and I need a bit of input.

At this very point I am getting a rb26 built to slap in my 2005 v35. Has anyone on here undergone this ? Please educate me if so. On what I may face during this swap over, and what I can do to eliminate any hiccups.

 

thank you in advance 

Link to comment
https://www.sau.com.au/forums/topic/473819-v35-rb26-conversion/
Share on other sites
Leroy Peterson Grand Master

Leroy Peterson

Posted
Posted

Google it. There's a few builds around, mostly from early 2000's when V35/G35 was newer.

Everyone seems to completely agree it's a waste of time and money.

What would the car be used for? Would you be doing all the work yourself?

  • Thanks 1
Ali Rookie

Ali

Posted
  • Author
Posted (edited)

Well you can turbo the original engine. But compression on it is always different to get it up and running you’re looking at about 8 plus thousand. So I don’t get the idea of being cheaper! 

 

The RB 26/30 doing all the internals on the bottom end, custom plenum on the head.

fabricating new engine mounts 

Slight fabs for the gear box 

computer/tune 

12g 

With the work that’s getting done I’m looking about 400kw on the rear.

trust me guys not much more expensive then turbo charging the vq35dett engine 

Edited by Ali
Ali Rookie

Ali

Posted
  • Author
Posted

@Leroy Peterson as I stated in my initial post, has anyone undergone this process to there v35. I am just starting this process now. I never asked for help just wanted to know if anyone on here has done it.  

My Brother and I, are doing it. 

 

@Ben C34 Sydney Australia. Setting it up for the quarter mile & street car 

GTSBoy Grand Master

GTSBoy

Posted
Posted
2 minutes ago, ADDSKI said:
On 4/20/2018 at 9:20 AM, GTSBoy said:
3.5L > 2.6 L.
More sense would be to swap in VQ37HR + boost.

well if you going to make such an effort. Why not a VK45DE.

Well, now we're talking about choosing between a much more modern all alloy V6 that is more likely to fit into the engine bay, or a vintage all iron low performance V8 that is likely to be too long, too heavy, too wide.......

ADDSKI Contributor

ADDSKI

Posted
Posted
Well, now we're talking about choosing between a much more modern all alloy V6 that is more likely to fit into the engine bay, or a vintage all iron low performance V8 that is likely to be too long, too heavy, too wide.......
You can't be serious. Annihilate all. Watch old yes and no.https://youtu.be/dE76eJjVIac.
To be honest V35 wheelbase platform has far far greater capabilities and stability than any Rb26 could ever offer
ADDSKI Contributor

ADDSKI

Posted
Posted
You can't be serious. Annihilate all. Watch old yes and no.https://youtu.be/dE76eJjVIac.
To be honest V35 wheelbase platform has far far greater capabilities and stability than any Rb26 could ever offer
They are all alloy engine, that produce 254kw as base. Nismo racing in Super Gt series opt for this motor over the Nissan Gtr VR38DETT.....OH YES YOU CAN MAKE IT FIT.
sonicii Veteran

sonicii

Posted
Posted
1 hour ago, ADDSKI said:

well if you going to make such an effort. Why not a VK45DE.

There has been some with VK56DE (at least in a 350Z), but it is very tight fit and no space left for turbo charging.

I suspect you could extra better performance with a boosted VQ37 than an NA VK, as well as being easier to fit.

ADDSKI Contributor

ADDSKI

Posted
Posted
There has been some with VK56DE (at least in a 350Z), but it is very tight fit and no space left for turbo charging.
I suspect you could extra better performance with a boosted VQ37 than an NA VK, as well as being easier to fit.
Yeah I just thought the original idea wouldn't be worth doing. So just through in the idea of VK45DE

Sent from my SGP611 using SAU Community mobile app

GTSBoy Grand Master

GTSBoy

Posted
Posted
1 hour ago, ADDSKI said:
1 hour ago, ADDSKI said:
You can't be serious. Annihilate all. Watch old yes and no.https://youtu.be/dE76eJjVIac.
To be honest V35 wheelbase platform has far far greater capabilities and stability than any Rb26 could ever offer

They are all alloy engine, that produce 254kw as base. Nismo racing in Super Gt series opt for this motor over the Nissan Gtr VR38DETT.....OH YES YOU CAN MAKE IT FIT.

Sorry, was thinking VH with the iron block thingo.  But nevertheless, 254kW from 4.5L is not strong.  VQ37VHR makes essentially the same stick from just over 80% of the capacity.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Ahh. Well the block damage is a problem, you really need to run a tap or thread chaser through it to see if the threads can be saved, but any chips are likely to be bottom end bound which is bad. Earls seem to have what you need if you want to stick with mounting direct on the block: https://rceperformance.com.au/parts/earls-straight-adapter-1-8-npt-male-to-1-8-bspt-female.html, but as I said above I'd recommend remote mounting the sender
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm not quite understanding or I'm missing steps here, (I appreciate people are trying to inform my brain but I am of the dumb, especially today) - All I want to do is mount the male BSPT of the OEM sender into the system somewhere without it snapping the adapter via vibration. The Nissan sender has a male 1/8 BSPT output. The block has a (very destroyed) 1/8 NPT input. I'm not really sure how a lathe assists with that, and also don't know anybody with a lathe, nor specifically what I would want to buy. I'm not really sure how adding additional adapters creates a better, more leak proof resilient seal here.
×
×
  • Create New...