Jump to content
SAU Community

Recommended Posts

Hi guys

 

I have an R34 GTT and am concerned with the boost levels it's running. It has some basic bolt-ons including a front mount intercooler, full 3inch de-cat turboback exhaust, apexi pod filter and custom cold air intake. The stock 2-stage boost controller has also been grounded out.

 

However I've been having issues with how much boost it's running. It's occasionally hitting the 1bar mark on the factory boost gauge, and it does not have a boost tap. I believe that was causing issues as the car had severe flat spots through the rpm range and was missfiring and spluttering occasionally on boost. I read up and unplugged the factory 2-stage controller and it now sits on 7psi constantly, which i'm much happier with.

 

My 2 questions were, why/how is it boosting this much without a tap or controller, and could the missfire/break up I was getting on boost be because of the boost levels it was running? Feels fantastic on 7, and pulls properly the whole way to redline. Have checked and gapped my spark plugs to .85 too. Was planning on getting it tuned on a link ecu but just wanted to check for ideas here first about those two things.

 

Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/474040-r34-gtt-running-too-much-boost/
Share on other sites

Probably not misfiring.  Could be, but probably not.  The standard ECU gets really upset if you go over about 12 psi.  First you get rich & retard.  Then it starts boost cutting, which feels like a miss.....because it is....just a deliberate miss.

As to why it's overboosting.....who knows?  The factory boost "leak" through the solenoid might have been made a lot larger, which will raise the boost above the ~7 that it is supposed to run.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...