Jump to content
SAU Community

Recommended Posts

2500km after the last oil change and I've just had to add 1.5l of oil to get back up to the "full" mark. That sounds pretty wrong to me but there are a few sources online that say 1L/2500km is normal for most cars and I found one that reckons the vq25de specifically can use 0.5L/1000km which means mine is normal, What have you guys experienced?

39 minutes ago, GTSBoy said:

That's "normal" in dealer speak, where they don't want to have to do any warranty work. I never check the oil in my Neo25 in the 10000km between services. If it ever starts using oil, I might be in trouble!

If you never check it how do you know it isn't low on oil?

41 minutes ago, Ottdurr said:

If you never check it how do you know it isn't low on oil?

Because it doesn't use oil. I do the same with my daily cars, they don't use oil, so I don't check. Once you get a idea the engine doesn't use any noticeable amount of oil you can stop checking!

Im your case you car burns a fair bit if oil, so you need to keep an eye on it. To me that's a mental amount of oil, but really it's not like you are going to rebuild the engine just because of that

 

  • Thanks 1

That's high oil consumption. Worth trying to find out where it's going. Oil you are using could be too thin also...

Checking oil every few weeks as a minimum is a good habit to get into, weather the engine looses oil or not. It's an expensive repair if it runs out.

Early Holden Barinas are “allowed” according to golden to use 3.5l per 10k they hold 3.7l and service intervals were every 15k. So if unchecked it could use all the oil before the next service!?‍♂️

2 hours ago, RBW49N said:

Early Holden Barinas are “allowed” according to golden to use 3.5l per 10k

Not the Suzuki ones, surely? That would have to be the shitty Spanish built Opel ones, and if so, no-one would cry if/when they died. That's just natural selection.

  • Haha 1

My VQ25DET was needing about 0.5-1L of 0W-40 per 5000kms, but the cam cover gaskets have been changed (pink slip fail) so hopefully that consumption will reduce (not that the garage floor showed more than the occasional drop of leakage..).

The VQs came at the start of the era when OEMs were staring to use very thin piston rings and other design/spec choices like low ring tension, intended to reduce fuel consumption. Subaru motors got the worst of it, because there's nothing worse than a piston ring design that allows more oil to pass, on a horizontal cylinder.

On 27/12/2019 at 11:36 AM, GTSBoy said:

Not the Suzuki ones, surely? That would have to be the shitty Spanish built Opel ones, and if so, no-one would cry if/when they died. That's just natural selection.

Yeah the shit Euro ones not the quality Japanese ones

On 27/12/2019 at 4:04 PM, GTSBoy said:

The VQs came at the start of the era when OEMs were staring to use very thin piston rings and other design/spec choices like low ring tension, intended to reduce fuel consumption. Subaru motors got the worst of it, because there's nothing worse than a piston ring design that allows more oil to pass, on a horizontal cylinder.

My Pooparu hit 256,000 km (EJ255), and yeah it does burn an alarm amount of oil for me (almost 1L per 10,000 km). My GT-R doesn't burn oil and it's 1990 model.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nice, thanks for sharing your progress....that's a pretty long list you are putting into it!
    • Decided to upgrade my pressurised plastic coolant expansion tank for a fancy pants alloy version The OEM versions can get brittle, even the new plastic one I got when I first got the car is a starting to show signs of "stress" I wasn't cheap, but it is basically unbreakable
    • Morning all, I have an RB25DET Neo that's in need of a rebuild. Will need new pistons etc due to detonation damage. Would anyone be able to recommend a shop in Southeast Queensland who I could bring my long motor to for a rebuild? Just want someone who knows RBs and whos built a bunch of them before. TLDR - recommended engine shops for RB rebuild.
    • Gday Thought it was about time I started a build thread! As expected this project has snowballed into a huge financial liability, but unless you’re strong willed and responsible, it’s not a surprise. Background -  My first turbo car was an R32 GTS-4, got my full license and then totalled my Au Falcon a week later, so while trying to sell my RMZ450 dirtbike to buy another car a bloke offered to swap the R32 which at the time I felt like I was ripped off but looking back and seeing prices of those now ($40kish) it was a good deal, I didn’t know enough about these cars to appreciate what I had so sold it before the RB20 blew up. Between here and there, out of 12 cars I’ve owned the note worthy ones are a V8 Lexus SC400 (soarer), a couple of XR6 Turbos and my beloved S15 which I had for about 3 years, picked it up for $12500, repairable write off but she was fine, gun metal grey/pewter and bone stock/unmolested until I got my hands on it. Ended up spending about the value of the car and 280kw, 2 demerit points by the time I got defected and sold it for $14500 (also $40kish in today’s market, rip) Fast forward to the present day, I’m in a much better position financially and daily an MQ Triton (great cars, pipe down Ranger Bois), I cruised marketplace and car sales for a few months looking for another R32, the best deal I could find was an absolute rust bucket half finished project for $12000, until this R33 popped up in Port Macquarie for $18k - unregistered and barely running but decent shape, kept an eye on it for a few weeks and the price steadily dropped, $16k then $15k then $14k, that was the point where I was like shit someone’s gonna snatch this up! It was owned by a young bloke who had big plans but him and his missus just had a baby so smartest move financially for them but big gain for me. So 2 days later I’m towing a car trailer to pick this thing up. Roughly 2 weeks and $3500 later I’m cruising around Newcastle in my beat up R33 all smiles and dose noises! It only needed some basic shit to get it going, coil packs and air flow meter, electrical stuff and all fluids changed, 158k kms and running pretty good, nice smooth engine after oil and coolant flush - when I say coolant I mean it had been filled up with tap water, every gallery and heater element was filled with rust, 8-9 flushes later and still had brown liquid coming out but she’ll be right. The car was painted R34 Bayside Blue at some point but whether it was a cheap job or just not looked after is anyone’s guess, clear coat flaking like sausage roll.  Was rethinking my choices and contemplating life, had it up for sale for $22k - still cheaper than any registered R33 but got little interest, next minute I had an opportunity at work - 6 months overseas for good money, so that was a no brainer, fast forward again and here we are with a 50% finished project. Current Mods - 200ish KW according to butt dyno Was tuned with Apexi PowerFC EBC (old school Greddy Profec)  Stock turbo (more shaft play than a Tinder date gone right) 3inch turbo back Varex muffler  Aftermarket injectors of mystery size, Power FC showed 36% duty cycle at full boost so not behd good size Someone had good intentions but stuck with the stock R33 MAF so we had misfires at 6000rpm due to the MAF hitting 5.2V So far I’ve redone the entire interior with carpet form Car Mats Direct, new Seats and steering wheel from Autotechnica, also sound system by Autobarn (mainly Kicker) Also MCA pro comfort coil overs - Hands down best purchase yet, worlds of improvement over the tired 30yrold shocks Goals - 450kw/600hp on flex tune New paint job - Midnight Purple 2 Engine is at the shop getting rebuilt with forged rods a pistons, new valves and springs, ATI Harmonic balancer, Aeroflow 7.5L sump, rear head drain and oil restrictors as per oil control thread* and cam covers modded for larger breathers, other stuff I can’t recall of the top of my head Parts purchased and to be installed once the engine is done -  Engine loom from Wiring Specialties including these options: Haltech Nexus S3 R35 Coil pack conversion  PRP Dual Trigger kit Fan controller  Other Parts -  262 Kelford Cams Turbo - Hypergear ATR43SS3-ProS with T51R mod (whistly boi) 6 boost manifold (high mount) 50mm Turbosmart Pro gate (plumbed back for legal reasons) HKS Super Turbo Exhaust with High Flow Cat Custom 3.5inch dump and front pipe 1500cc Bosch injectors  Fuel Pump walbro 525 Haltech MAP and IAT sensors Haltech Flex Sensor Fenix Radiator with dual thermo fans LS1 Alternator Kit Oil Filter Relocation from EFI solutions and Cooling pro oil cooler Many other things sitting in my garage waiting for that engine to come back. Progress pics to follow -  
    • Losses have to be less with DC coupling. Provided the battery inverter has decent MPP tracking ability - which really shouldn't be a problem. It's not 2005 any more.
×
×
  • Create New...