Jump to content
SAU Community

Recommended Posts

Hi Everyone. 

So we've installed a HKS Step Pro VCam kit to my RB26 2.8L engine. (Dry sumped etc)

Head has had a full overhaul in the past - 1mm oversize valves, Shimless Buckets, 150psi aftermarket springs etc. 

So the issue i have is the VCam system can't advance unless the RPM is at 3500rpm or more. I have eliminated all electrical Issues / ECU control issues. 

The oil pressure feed line has been moved somewhere where there is plenty of oil (engine has a dry sump with heaps of pressure), and the VCam itself has been disassembled and checked thoroughly.

Could there be a chance the valve springs are too heavy for the VCam system to open the valves at lower RPM and oil pressure?

Anyone have any ideas? 

Thanks

Link to comment
https://www.sau.com.au/forums/topic/483648-hks-vcam-step-pro-issues/
Share on other sites

On 5/16/2022 at 9:06 AM, The Mafia said:

Could there be a chance the valve springs are too heavy for the VCam system to open the valves at lower RPM and oil pressure?

I can't see how that could be the case. All it has to do is rotate the camshaft, which the camshaft is already doing and already popping the valves open upon demand. The real counteracting force against the oil pressure is the return spring in the positioner itself, no? So, whilst it is difficult to blame the valve springs, your theory might, could, just possibly have something in it.

I suggest fitting a pressure gauge to the supply line close to the actuator and see what's what. Maybe the pressure there is disappointingly low until 3.5k.

We installed a pressure gauge right on the side of the cam cover, 40psi at idle couldn't move the cam. Had to increase the rpm to 3500rpm (100psi) and it started to move. 

I've asked so any people - No one is sure. 

On 16/05/2022 at 12:23 PM, r32-25t said:

When you opened the the cam gear did you tighten the back up with the cam installed in it and made sure the backing plate isn’t touch the cam at all?

I'll find out mate

Currently installing a V-Cam also. So following thread with interest.

In the instructions it does recommend an upgraded oil pump due to the pressure required by the vcam.

40 psi at idle is pretty stout though, can't imagine that being an issue if the flow is good.

 

For my own interest, how are you confirming that it is or is not opening the vcam ?

What are you using to control the vcam ?  Assume an ecu over the HKS control box ?

 

My only suggestion to help and I am sure you have looked at this is go through the o-rings(Cam cover ones especially).

If one is pinched, 40 psi at cam cover is going to result in a lot less to cam gear if you have a leak.

 

I agree with others above, the valve springs should have nothing to do with this.

 

On 16/05/2022 at 1:02 PM, Butters said:

Currently installing a V-Cam also. So following thread with interest.

In the instructions it does recommend an upgraded oil pump due to the pressure required by the vcam.

40 psi at idle is pretty stout though, can't imagine that being an issue if the flow is good.

 

For my own interest, how are you confirming that it is or is not opening the vcam ?

What are you using to control the vcam ?  Assume an ecu over the HKS control box ?

 

My only suggestion to help and I am sure you have looked at this is go through the o-rings(Cam cover ones especially).

If one is pinched, 40 psi at cam cover is going to result in a lot less to cam gear if you have a leak.

 

I agree with others above, the valve springs should have nothing to do with this.

 

Hey mate, we double checked the o-rings. One was pinched and we replaced it and it had the same behavior. 

Cam is being controlled with an Emtron KV8. To bypass all of the ECU side of things we connected the solenoid directly to 12v and ground and had the same result. Cam wouldn't move until 3500rpm on the trace in the ECU. 

Something is not right. It's frustrating that's for sure. 

On 16/05/2022 at 12:23 PM, r32-25t said:

When you opened the the cam gear did you tighten the back up with the cam installed in it and made sure the backing plate isn’t touch the cam at all?

Can confirm all of this went back together correctly 

On 5/16/2022 at 11:28 AM, The Mafia said:

Hey mate, we double checked the o-rings. One was pinched and we replaced it and it had the same behavior. 

Cam is being controlled with an Emtron KV8. To bypass all of the ECU side of things we connected the solenoid directly to 12v and ground and had the same result. Cam wouldn't move until 3500rpm on the trace in the ECU. 

Something is not right. It's frustrating that's for sure. 

 

So to be very specific . The KV8 is sending PWM to the negative side of the solenoid at a specific RPM say 2000 ?

Then you are reading the reluctor sensor on the side of the cam cover to see the advance ?

And not seeing a change in the cam until 3500rpm ?

 

Yep, that's it. ECU was reporting the cam angle.

A quick test to rule out solenoid control was to get a tail, plug it into the solenoid, and give it 12v and ground directly. It wouldn't move until 3500rpm and 100psi on the little gauge we had inbetween the line and the cam cover. Exact same behaviour as when the ECU was trying to control it. 

I was doing some data stuff on my car which is also dry sumped and we didn't want the engine running, so used a Subaru cam belt (15km long) and a dry sump mandrel on a power drill. This allowed us to spin the pump independently of the engine and log some data, and the drill can be located in a convenient location without some poor bastard on his back under the car.

Perhaps you could do this and see if there's any other weird shit going on? Overall oil pressure isn't your problem, so it's leaking out or you have a faulty solenoid. Alternatively there's something mechanical dragging on the gear, as above it's got nothing to do with valve springs.

  • Like 1
On 16/05/2022 at 4:48 PM, Komdotkom said:

I was doing some data stuff on my car which is also dry sumped and we didn't want the engine running, so used a Subaru cam belt (15km long) and a dry sump mandrel on a power drill. This allowed us to spin the pump independently of the engine and log some data, and the drill can be located in a convenient location without some poor bastard on his back under the car.

Perhaps you could do this and see if there's any other weird shit going on? Overall oil pressure isn't your problem, so it's leaking out or you have a faulty solenoid. Alternatively there's something mechanical dragging on the gear, as above it's got nothing to do with valve springs.

Hi Mate, I have two VCam kits, we swapped the solenoid and that didn't help either.

We've ruled out quite a few things that's for sure. 

My money is still on an oil pressure drop post cam cover.

 

The other thing you have to question here is the data sampling and again I am sure you have done this but given we are running out of ideas :D

 

I am wondering if it is actually activating before 3500rpm and your only seeing the change in the data at the point.  Simple things like only log  after 3500 for all parameters :)

Are you holding the engine steady at 3000rpm for a period of time and activating the solenoid and seeing no change in the KV8 data ? 

On 17/05/2022 at 10:33 AM, Butters said:

My money is still on an oil pressure drop post cam cover.

 

The other thing you have to question here is the data sampling and again I am sure you have done this but given we are running out of ideas :D

 

I am wondering if it is actually activating before 3500rpm and your only seeing the change in the data at the point.  Simple things like only log  after 3500 for all parameters :)

Are you holding the engine steady at 3000rpm for a period of time and activating the solenoid and seeing no change in the KV8 data ? 

The sampling data was live mate. from idle to 3500. It's like the VCam couldn't move under 3500rpm (Oil pressure I'm thinking) because at 3500rpm the pressure at the guage was going over 100psi. Under that it couldn't control the position properly. 

When the oil was cold it was a little under 3500rpm which makes me think it's a pressure / flow / resistance (springs) issue. 

New springs are going in and I will report back. 

On 5/16/2022 at 9:59 PM, The Mafia said:

The sampling data was live mate. from idle to 3500. It's like the VCam couldn't move under 3500rpm (Oil pressure I'm thinking) because at 3500rpm the pressure at the guage was going over 100psi. Under that it couldn't control the position properly. 

When the oil was cold it was a little under 3500rpm which makes me think it's a pressure / flow / resistance (springs) issue. 

New springs are going in and I will report back. 

There is some kind of locking pin on the VVT cam gear that holds it in place during cold start and other conditions where the VVT is not going to work properly. So you're going to have to trace the path from the gauge to this pin and verify there's no weird behavior like leaks, etc.

Okay, so changed the valve springs and the VCT works as it should now (nice and responsive at idle). 

125psi springs were just too heavy for it. 

I have heard that when people have put heavier springs in the Barra those have stopped working too. 

Currently running HKS springs. 

I recommend lighter springs 90psi would be pushing it. 75psi or below will be my safe estimation.

(Please bear in mind your RPM targets, cam selections, etc). It's a careful balancing act. 

Edited by The Mafia
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...