Jump to content
SAU Community

Recommended Posts

I'm trying to prep the dirty 30 (330i) for sale.

One issue I have is that the car becomes deafening at around 60 - 70kph. The noise is definitely wheel speed related rather than revs. It sounds like loud-tyre noise but amplified 10 times. There doesn't seem to be grinding or metal-on-metal etc.

I've done the diff fluid on this car about 12 months ago. I believe the noise was occuring then also. Made no difference.

I'm leaning toward bad bearing (passenger side done last year) but I've never heard of them being *this* loud. You honestly can't have a conversation.

Any ideas?

Thanks guys.

 

wheel bearing is normally a whoomp whoomp noise like a falcon taxi. If it is bad enough to be a grinding noise you might be able to confirm by jacking wheel off ground and trying to wobble it side to side.

also, generally the outside bearing is noisy in turns so that might help narrow down the side

  • Like 1

Diff or rear wheel bearings. It kinda has to be. (though it could be a tailshaft... what else rotates back there?).

The comically loud diff whine I have had in the past was due to the crown/pinion gear being f**ked. Messed up bearings is generally a low grinding/rumbling sound.

Diff is usually a much higher pitched whining...right?

I've had a wheel wobble so badly it almost fell off, and I wouldn't say it was ever loud enough to be conversation-stopping, whereas diff whine was alarmingly loud, piercing but the car "drove fine".

Wheel bearings.

I've had two cars do it like that.

One was a Honda Jazz. Horrible just loud deep noise, exactly as you describe, sounds like road noise but 10 to 20 times louder.

 

Second was our Subaru Liberty GTB.

Exact same thing. The part that made this one harder to diagnose. The wheel wobble didn't exist. "Sealed" bearings that dried out, and got silly loud.

 

Way to identify, is have someone stand on road side, drive past at about 60.

Turn around, go back the other way. Side that's louder is your bearing issue.

 

Diffs typically have a higher pitch noise than the sound of road noise.

 

So far had 3 wheel bearings go on 3 different cars, only one went whomp whomp whomp like Duncan said. Funny part, it was a Ford Falcon that did it! Bahahaha

  • 11 months later...
35 minutes ago, GTSBoy said:

Good one @PranK. A year later and no update on the cause of the noise.

Woops, forgot to update.

Yep, was the bearing. And, still havent sold the car! 

 

Thanks all for the replies! SAU crew to the rescue once again! 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
×
×
  • Create New...