Jump to content
SAU Community

Recommended Posts

Hi guys,

I was considering buying a RB25DET NEO AWD from a C34 Stageau. I was expecting to swap the sump and pickup and that was it, which is what the engine importer lead me to believe. 

Being cautious I did some research and it appears the oil pickup inlet on the block is in a different spot to the RWD so even using RWD pickup it will be in the wrong spot in relation to the sump? 

It also looks like the steel braces that go from the block to the gearbox are not able to be used when using the AWD block as the provisions for the brace to bolt to are not there. 

Can anyone please confirm the above, its hard to get a definite as posts are contradicting - I am hope someone here has done the conversion and can tell me from experience. 

Best regards,

Blake.

Link to comment
https://www.sau.com.au/forums/topic/484568-rb25det-neo-awd-into-ecr33/
Share on other sites

Yes, I did the same thing before.

You'll need a new pick up, new sump. The brackets cannot be used. At the time I ended up an ASR kit, made for a RB26 to RWD conversion sump.

Food for thought, because the oil pick up is moved forward you'll in theory be pulling oil from a higher oil level when your rear end squats and/or your front end is elevated during heavy acceleration.

I cannot confirm if this is the root cause of my previously built motor lunching itself however it was due to oil starvation (which could have been from various things).

The problems are in converting a 2rwd (eg rb30) block to 4wd, in that case the oil pickup fouls the front driveshaft in the sump, and the block is not drilled for 4wd sump bolts (thus the 2wd to 4wd conversion plates).

Using a 4wd block in 2wd should just be bolt on, noting the pickup location is different. It looks like the setup dose posted uses a custom pickup, probably because the sump well is deeper. If you try and move the pickup to the standard location you will have to drill to the oil gallery as the flange is in the casting but the feed is not drilled (and obviously you have to block the original pickup gallery with a plug)

  • 4 weeks later...
6 hours ago, QLDR31 said:

If I was putting an awd engine into a rwd car. id keep the awd sump chop the front diff part off and weld up the holes. Hopefully there is no space issues with steering rack etc.

Pretty sure front vs rear sump is a matter of what will actually package for your particular swap. And if I could decide either way I suspect rear sump is better as under acceleration the oil probably can be controlled more easily with a rear sump. Front sump once it escapes the windage tray it really isn’t going to drain back until you let off. 

  • Like 1
18 hours ago, QLDR31 said:

If I was putting an awd engine into a rwd car. id keep the awd sump chop the front diff part off and weld up the holes. Hopefully there is no space issues with steering rack etc.

This is what most people do, you have to grind the fins on the bottom of the sump for a bit of clearance.

 

12 hours ago, joshuaho96 said:

Pretty sure front vs rear sump is a matter of what will actually package for your particular swap. And if I could decide either way I suspect rear sump is better as under acceleration the oil probably can be controlled more easily with a rear sump. Front sump once it escapes the windage tray it really isn’t going to drain back until you let off. 

R33 is front sump, not many rb cars are rear sump, z31 rb20 is rear but haven't seen any others.

  • 5 months later...

It would be better to have lower bolts between the block/sump and gearbox, but plenty of people go without, including my 400kw Stagea.

There are weld on extensions for the gearbox so it bolts up OK

20 minutes ago, Dylank said:

So is it fine to not have any bracket from the engine to gearbox?

I didn't have it with the last motor, and it visually it seemed fine.

Went to 2x track days and 2x skid pans with 407kW. Motor did explode afterwards, however no correlation to not using the brackets.

  • 2 weeks later...

Cheers guys I've got a mate doing the awd sim for me so I'll have the bottom bolts to use in bell housing. What did you guys do with the wiring and computer. Should I use the loom in my series 1 r33 gtst or the loom that can with neo stagea engine. 

It's a blue plug 33 ecu/loom?

Probably the easiest way is to use all the 33 ancillaries on the neo, not ideal but works, nistune be a good idea, if it's alloy cas you'll have to reverse the wiring and coil mounts might be different, otherwise wire the neo loom in.

 

 

Edited by WMDC35
  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...