Jump to content
SAU Community

Recommended Posts

(context, my rb25det pull type gearbox was making a grinding sound on idle and when accelerating in the lower rev range but goes away with the clutch pedal in) I got a pretty hefty bill recently which I'm not overly happy about (only because the problem is still there), my mechanic told me a while back that the grinding noise I had in my car was the spigot bearing, long story short but he pulled it out and it looked like brand new, he said that it wasn't lubricated and ended up putting in a new one that was. I didn't think much of it, until I turned on the car went for a drive and noticed the car has the EXACT same sound, nothing has changed.

He said it had some noise which I have no idea what he's referring to and I told him that my gearbox was still grinding, when we went for a test drive he said it was normal. There's no way a grinding gearbox is normal. You can really hear the grinding if you're in a higher gear but your speed is low, I guess makes sense as the gearbox is working harder.

That's one issue, the other issue I noticed is there is a loud rattling sound especially when I start up the car and especially as I go up my driveway. Some other things to note is that the previous owner did a dodgy clutch install and also stripped one of the threads on the flywheel bolt which my mechanic all fixed up and put a new clutch kit in, which I'm not sure if that has something to do with it. I know a bit about the history of the car, it was definitely thrashed and tracked.

The car itself drives fine and doesn't crunch through the gears, there was wasn't much metal shavings on the gearbox. Do you believe my mechanic misdiagnosed my car? I'm trying to decide what next steps to take, I imagine I'll have to rebuild my gearbox eventually.

Edited by silviaz
Link to comment
https://www.sau.com.au/forums/topic/484997-did-my-mechanic-misdiagnose-my-car/
Share on other sites

I don't think you can blame the mechanic. He replaced what he thought and what is a common source of gearbox noise. It could be internal gearbox bearings that are causing your noise. Would have been an even bigger Bill. These boxes are a little noisy at low revs high load. I had a brand new one in mine before I broke it and it also had noise at low rpm.

I'd just put up with the noise and don't load it up at low rpm. Gearboxe is trying to tell you it doesn't like it.

  • Like 1
9 hours ago, GTSBoy said:

Input shaft bearing, more than likely. More common on the skinny box, but still an issue on the fat box. Mine does it (groans and resonates at low rpm in higher gears).

Funny thing is I wanted that replaced but my mechanic said it's a rebuild at that stage, I wanted that replaced because from what I understand it's not deep in the gearbox. 

11 hours ago, admS15 said:

I don't think you can blame the mechanic. He replaced what he thought and what is a common source of gearbox noise. It could be internal gearbox bearings that are causing your noise. Would have been an even bigger Bill. These boxes are a little noisy at low revs high load. I had a brand new one in mine before I broke it and it also had noise at low rpm.

I'd just put up with the noise and don't load it up at low rpm. Gearboxe is trying to tell you it doesn't like it.

Yeah, problem is would have been better to do it all at once but now I have to pay to pull out the gearbox again.

4 hours ago, silviaz said:

Yeah, problem is would have been better to do it all at once but now I have to pay to pull out the gearbox again.

Weird to me how the mechanic didn't offer to just tear into it further at that point but that's just how it rolls with a lot of mechanics. They'd rather get the cashflow sooner than later.

5 hours ago, silviaz said:

Funny thing is I wanted that replaced but my mechanic said it's a rebuild at that stage, I wanted that replaced because from what I understand it's not deep in the gearbox. 

Well, replacing a front bearing is not a "rebuild", nor does it trigger a need to rebuild everything in the gearbox. A dismantled gearbox with worn/aged parts can be put back together just fine. The only argument is whether the labour to do so is then considered to be wasted compared to doing a rebuild as well.

3 hours ago, joshuaho96 said:

Weird to me how the mechanic didn't offer to just tear into it further at that point but that's just how it rolls with a lot of mechanics. They'd rather get the cashflow sooner than later.

Nah this mechanic is honest and for him he has a more "leave it if it's working" approach. Not always ideal because if for example I didn't replace my rear main seal and it leaked then I'd have to pay him again to pull out the box.

2 hours ago, GTSBoy said:

Well, replacing a front bearing is not a "rebuild", nor does it trigger a need to rebuild everything in the gearbox. A dismantled gearbox with worn/aged parts can be put back together just fine. The only argument is whether the labour to do so is then considered to be wasted compared to doing a rebuild as well.

Yeah that's what I thought, I thought if all he has to do is take off the input shaft cover and replace the bearing behind it, that sounds like a pretty easy job but I'm not 100% sure as I haven't been able to find much information on the process.

3 hours ago, silviaz said:

Yeah that's what I thought, I thought if all he has to do is take off the input shaft cover and replace the bearing behind it, that sounds like a pretty easy job but I'm not 100% sure as I haven't been able to find much information on the process.

No it’s not that easy, you need to completely strip the box in order to get the input shaft out and press the bearing off it and press the new one on 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...