Jump to content
SAU Community

Recommended Posts

how do i get the Flutter sound on my s2 gtst?

i was at a wrecker and this guy came down changing gears letting off this cool flutter sound into the atmosphere

i asked the guy how he did it but he did go into much detail i guess he want to keep it a secert

he briefly said that he blocked off the BOV and he asked if i had a aftermarket air filter, he said thats all i needed to get that sound

i really wanted the flutter sound because it sounded MAD

i want to know if anyone knew how to do this?

Link to comment
https://www.sau.com.au/forums/topic/60655-flutter-sound-as-bov/
Share on other sites

  • Replies 300
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

What else do you need to know? As it was said, you just take off the standard BOV, block off the hole it leaves, and install an aftermarket pod filter on, and you'll get the same noise...

Most people seem to think its bad for your turbo (its what causes the flutter noise) and i agree with them.

well i got the fluttering noise on my car, its pretty sick, especially if you run full boost, thaz when its loud of its head.

When u do the "cooler noise" i call it, in front of ppl, every cnt looks at you mate. Its like you are a celebrity mate. but you gotta be carefull, read reasons below:

1) Attracts chix, but so does it the Cops

2) If you boost your car, you are more likly to blow it (been there done that)

3) it will stuff up your idleling, and in lots of cases your idel will be unstable, even if you go back to your original setup your idel remains unstable, as the AFM meter re-programs itself in a way.

4) ITS ADDICTIVE (trust me, once you put it on, you wont be taking it off)

P.S. To get it very loud, you should run higher boost, and have a big front mount cooler, and the POD, dnt worry about it, just run a 90 degree elbow from the turbo. and off you go.

Just be aware of the consequences below:

1) Get canary (defect sticker) easy as

2) Blow turbo

3) Very careful with this one, YOU MIGHT BE UP FOR A NEW BOTTOM END (been there done that)

The sound is wicked, but there are to many 'againsts' to have it on ya car. just get a after market BOV.

I had it on mine , I have a Blitz hybrid (atmo & plumb back) and had the plumbback blocked off as I did not have the right hose for it , it made a huge flutter sound ! but as everyone has said above it can cause serious damage to your turbo, suggest only using it for a short time !!!!!! if at all !!!

my 2 yen

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...