Jump to content
SAU Community

Recommended Posts

I need new tyres for my R33 GTS-4 (non-turbo 4wd).

Current tyres are 225/50/16 Sava Intensa, which seem to give adequate traction for my car.

I can get the same ones (Sava) for around $180each?

Cheaper Nankangs for around $120each

Or something like Goodyear Eagle F1s for $210each

They're the 3 I was told about today anyway.

Any suggestions?

Car is just a daily driver obviously and I want something that has decent grip in the wet too. Current tyres aren't too bad in the wet, it will only slide in the rain if you make it (obviously 4wd makes it harder).

I get $10 off a tyre, so F1s would be $800 fitted and balanced, which is probably the most I would want to spend.

I don't really want to get a cheaper tyre than my current Sava's so probably wont get the Nankangs but might consider the F1s if they are good?

Yeah thats definitely them. They cost good money as well.

I'd have to go with Duncan on the SP-9000's. I also found them an excellent road tyre, and would definatly use them again.

You must have got a bad tyre, incorrect suspension setup or tyre pressures to be unhappy with these.

I'd have to go with Duncan on the SP-9000's.  I also found them an excellent road tyre, and would definatly use them again.

You must have got a bad tyre, incorrect suspension setup or tyre pressures to be unhappy with these.

Hi Scotsman, my wheel alignment was done at East Coast Suspension which is supposed to be good. I have since found out though that I was not entirely fair on the sp9000's as I have never really liked the front end of my car and that was due to the front spring rates not being hard enough, the standard (too hard) bump stops and the whiteline swaybars being incorrectly set. I have had the bars fixed and it has made a big difference but it is bottoming out in the front all the time (only lowered 1 inch). Its not really obvious but you can feel it and it makes the car very nervous on imperfect surfaces (read: sydney roads).

I just need to get the custom springs made up and I have a funny feeling my opinion of the 9000's will change.

Hi all,

Just purchased an r34 GTT sedan, currently on bridgestone import tyres and handles great! Unfortunately I need to buy new tyres and am overwhelmed by the options including width, price etc.

Given that most half decent 225,45,17's start at $225+

Could someone provide some feedback on width?

I am running stock rims and unsure if I would get improved ride/handling by running wider rears? eg. 235 fronts and 245 rears?

Thanks...

I currently have Michelen Primacy, which are top of the range Michellen tyres.. Even tho i have bought second hand tyres, the grip on them is just to good.. They really stick onto the road.. even tho with 50% thread left, im really happy..

Got the primacy on z32 rims, with 215s/55/16s..

Worth checking out the primacy range.. But $$$$..

im digging into my pocket again for two tyre's

i bought some wide ovals for the front and i am happy with them but i cant get over the feel of my car with toyo tpg's on it's so gripy an with lots of rain coming down i dont even worry about slideing. @ $205 for 17's its a bit pricey the toyo 16's only cost me $165 its a big jump in price for one inch bigger rim delemas delemas

Nankang... they've done about 5,000kms, a track day of... "drift" (not overly, more grip sessions, but all 20min sessions and they still look and drive fine) have good grip in wet, and are... relative in the dry. HOWEVER, IMO all problems aside with every tyre I've ever tried is to do with varying power levels, driving conditions and how much abuse they sustain, also, suspension/braking and so on... as you can't really do a back to back test unless taking them to the track of a stack of lap and then comparing etc... SO there are a lot of variables when trying to compare tyres I think.

Cheers

Grant.

Just wanted to put a word in for the Bridgestone S-03s. These have done over 10,000 km on my car now and I just took them to a track day at Queensland Raceway where they did more than 30 laps (5 lap stints).

They're wearing ok (-1.5deg camber on the rear) and probably have about 5000km left in them, maybe more if I rotate them across the rear. They handled the track day well and didn't crap themselves though the front left looks a lot more average now than it did a week ago. :lol:

By lap 5 of each stint they were feeling a bit soggy but that's to be expected with a road tyre I guess.

I cannot say enough for these tyres in the dry, they are just so predictable and grippy. They're not so hot in the wet (sideways in 4th gear on the freeway, anyone?) but I am running about 240-ish rwkw with a 255mm width on the rear so they have their work cut out.

So yes they were freaking expensive but I'm not feeling overly ripped off. Next time I will probably try the Toyo T1Rs or those Revspec things (if I can find them) or maybe the Hankooks, but only if they're significantly cheaper than another set of S-03s. :(

Has anyone tried the S-03 vs something else?

hmm i thought primacy range were top of the list.. they are like 395bucks each tyre.. isnt that expensive..

I also have piolts hx on the fronts.. They are alright tyres as well, but they are getting really old, you can see marks on the tyres..

How much does the sport and the preceda cost?? Do they have more grip than primacy tyres??

hmm i thought primacy range were top of the list.. they are like 395bucks each tyre.. isnt that expensive..

I also have piolts hx on the fronts.. They are alright tyres as well, but they are getting really old, you can see marks on the tyres..

How much does the sport and the preceda cost?? Do they have more grip than primacy tyres??

nope just have a look on the michelin web site if u want more details. they are expensive but pilot sports are even more expensive :P and yes sports would have more grip for sure plus other sporty qualities.

Whoooohoooo :D

Just got my new T1R's on. I got 235/45ZR17 all round but found out i could have gotten 255 on the rear. The d@ckheads who serviced the car previously (before i owned it) had rotated the tyres. They put the 17x8 on the front and the 17x7 on the rear, thought it felt like crap.

Feels good so far but havent really tested them :D

The guy also mentioned that i should get a camber kit as one side is 1.3 and the other 2.

btw - Paying between 250-400 per tyres isn't exp to me, anything over that is though. Heard somone paid approx $800 per corner for pirelli 265/30's on 18 or 19 inch rims, no thats exp

:laugh: and yes sports would have more grip for sure plus other sporty qualities.

FUNNY - how so may I ask?? LOL

Just a point, I ran Pilot Sport for $220 (rear wheel, 17inch) on my Fireblade, and now run Pilot Power ($280). The Power is far superior to the Sport, and the Sport is a model that is around 3yrs old in the motorcycle industry... so maybe the Sport in car tyres is the older model, with Primecy being the latest model?

FUNNY - how so may I ask?? LOL

Just a point, I ran Pilot Sport for $220 (rear wheel, 17inch) on my Fireblade, and now run Pilot Power ($280). The Power is far superior to the Sport, and the Sport is a model that is around 3yrs old in the motorcycle industry... so maybe the Sport in car tyres is the older model, with Primecy being the latest model?

How so? well what i mean by sporty qualities is that they will last longer before turning to mush, grip more, and have stiffer sidewalls that improves grip and steering feel etc etc.

for cars its different, sport is the better one just look at the michelin website if u want to see for yourself :)

About to gat a set of 4 tyres, 235/45/17 for a budget of exactly $200 per corner.

Probably going to go the Hankook 104's for that price.... but what else compares to the 104's in regards to wet weather grip & matching price?

Cheers! :sorcerer:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • LOL.... a good amount of people (not all) on that continent seem to know everything and like to measure things in bananas, football fields, statue of liberties instead of the metric system lol.
    • I assume the modules are similar enough, so if you've had no issues I don't see why I would. I have tried to find a wiring diagram for the FPCM / fuel pump circuit, but I can't find it anywhere. Otherwise, I would just do some wire cutting and joining at the FPCM and give the 12 V supplied to the FPCM directly to the pump instead. If you know anyone that could help with wiring diagrams, I'd be very happy  
    • If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
×
×
  • Create New...