Jump to content
SAU Community

Recommended Posts

I'm running some Bridgestone RE540's on the R32 atm,

Brilliant dry grip - 10+/10

Normal wet weather grip - 7/10

Price 225 x 50 x 16 - $280 (on closeout)

The thing is that they are great on smooth roads, but due the the very stiff sidewalls and ~2 degrees of neg, they tramtrack badly over uneven surfaces and will unsettle the front through uneven roundabouts. I will be going back to a less rigid semi for my next purchase. Probably a Toyo RA1, my fav previous tyre, not quite as much dry grip as the Bridgestones (still far more than a street tyre), but better wet grip and a softer sidewall.

Jamie

Hankook Ventus K104

235/40/17

255/40/17

$860 fitted to R33 gts-t rb30 284 rwkw 947nm (bloody high-flow)

Don't really like them.

Straight line traction not too good, I know, (too much torque)

1st and 2nd forget it, 3rd so-so

Huge difference when hot or cold.

Feel stable at high speeds, good under brakes.

Hang on ok around corners after 4 laps at Oran Park but too much side wall flex.

Feel a little squirmy when hot.

6/10

  • 1 month later...

Nankang NS2 235/45 17's

Dry performance 6/10

Wet performance 3/10

In the dry once they are warm they were pretty good. though after 3-4 laps you could feel the sidewalls etc moving around. i was pretty happy

for them in the dry for what they are.

In the wet is a different story. No grip what so ever, the smallest bit of throttle would spin the rears and corner speeds would see the rear

the squirm then the front and end up in four wheel sliding, which was a quite unpredictable.

Federal 595RS 235/45 17's

Dry performance 8/10

Wet performance 8/10

While i was impressed with the dry performance of the ns2's these are in the different league. Worth 1-2 seconds on the track easy. corner entry

and mid corner grip is fantastic.

Performance in the wet is unbelievable, having grip turning in and around the corner is amazing. around longer radius corners i could feel the sideways moving around with a hot pres around 38-40. but this was at least quite predictable.

have done 2 track days now, one in the wet and done about 800km on them, only signs of wear are the sidewall fingers are all long gone.

  • 2 weeks later...

Unitrac focus2000 on stock 33 gtst rims watever size that is

Dry performance 5/10

Wet performance 0/10.. corners I previously took in the wet at 55-60k an hr in my fwd corolla on $60 mystery tyres cant even be taken at 35k an hour.. if I drive through a puddle at 60k an hour in a straightline I aquaplane while other cars pass me with ease at 70k an hour.

Value?/10 these came new with the car when I bought it so im guessing they were the cheapest tyres around, shows you get what you pay for I guess

Sumitomo HTR ZIII

235/40/18

$285 a corner fitted and balanced

Dry 8/10

Wet 8/10

Very stiff side wall, excellent tread design. Handled really well in the last couple of down poors in Adelaide. More grip when hot, but still good and predictable when cold. No where near as much shoulder wear as previous tyres.

KU36

225/55/16

$161 from option1

Dry Performance 8/10

Wet Performance 8/10

Great Tyre for the price, good comprimise between a track and road tyre and handles the wet well.

Still waiting for the right tyre sizes to be available such as 245/40/18 or 265/35/18 locally in Malaysia. Heard many good reviews in many forums. Still miss my Falken Rt615, anyone tested both to advice which is better?

  • 2 weeks later...
anyone had any experience with......

YOKOHAMA A032R

semi slicks?

Are these similar the...say falken 615's? etc? or a "true" semi slick?

Yeah I had to use them for years because they were our control tyres. They are proper semi slicks but rubbish for the price.

1-3 seconds slower than DZ03 or re55s

no they are too hard if anything, not too soft.

they will be fine if you are happy to go 2 sec slower :P

Just grab some re55s or dz03g to get best performance. Or maybe even yoko a050r.

i need to get new tyres asap, ive looked through this thread but everyone says diffrent things,

what are good tyres for a non turbo r33 gts4?

im thinking maey Federal 595 Rs-R

Edited by sydking
Sumitomo HTR ZIII

235/40/18

$285 a corner fitted and balanced

Dry 8/10

Wet 8/10

Very stiff side wall, excellent tread design. Handled really well in the last couple of down poors in Adelaide. More grip when hot, but still good and predictable when cold. No where near as much shoulder wear as previous tyres.

Definitely a very reasonably priced Assymetrical design out there. I was quite impressed with them also.

TOYO R1R

Dry Performance 9.5/10

Wet Performance 8/10

price for 235/45 R17

is $305 each, which isnt cheap but they do hold on really well and dont make any noise around a corner.

they give you so much more confidence when coming into a corner.

IMO the tyre is the best one you can get for street,

they're a little bit soft, and probably wont last the longest. but even normal city driving you can feel the heat in the rubber when you stop and feel the tyre.

final opinion:

they're not cheap, but well worth the cash if you're after a very high performing tyre.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...