Jump to content
SAU Community

Recommended Posts

im just wondering which of these 2 dump pipes will give you more power - screamer dump pipe or split pulse dump pipe?

Im looking at getting either one which works best for my RB25 Turbocharger im using on my RB20DET engine

Ive seen heaps of companys selling split pulse pipes on EBAY etc but not many selling screamer pipes, anyone know of any companys that sell screamer pipes?

if you want it too sound horridly retarded, get a screamer...

they sound VERY bad on small turbo/pipes IMO.

Heard them on SRs and its pretty p|ssweak compared to a big turbo with an ext gate

If you exhaust is 3" then get the one that plumbs in.

There shouldnt be a performance loss if its 3" to begin with.

Correct. On an internal gated turbo, and a RB25 one at that I would say get the split pulse dump that joins back to the exhaust system. Just get one that seperates the wastegate gasses for a decent length, say 300mm if possible. Not the ones you see that seperate it for 50mm.

A screamer version, which vents it to atmo "might" make a tiny bit more but is ridiculously loud which attracts unwanted attention and is also illegal to boot.

A screamer pipe or "divorved" downpipe will always give you more power.

Whether or not you want a louder exhaust is up to you.

Back to back tests were done on a 7M-GTE (3.0 liter supra turbo) using a full 3" downpipe that replaced that replaced the cast turbo elbow and all, vs. a full 3" downpipe with a divorced wastegate or screamer pipe as you call it.

The result was a gain of 22 wheel horsepower from just the screamer pipe. This was done on a bone stock motor with only a cat back and an air filter + the 2 aforementioned downpipes.

Pretty big difference if you ask me.

you'll only have a gain if the exhaust is restrictive enough that you loose power.

There are a few cars the come to mind that have been tested with/without the atmo gate (on bigger cars) and there is no loss.

mind you this is using 4" exhausts and stuff. But for a small turbo setup that obviously flows a lot less... should b arite

  • 1 month later...

screamer pipes are somewhat illegal, anyonet hat thinks that this noise is tops, well drive ur car to a racetrack or drag strip. Put it on, and go for a hoon, then take it off again and drive home. On a street car i beleive it is a stupid idea. :D

have a nice legal streetable car. be it mostly legal. hehe

peace out, yeahhhhhhhhhhhhhhhh

Back to back tests were done on a 7M-GTE (3.0 liter supra turbo) using a full 3" downpipe that replaced that replaced the cast turbo elbow and all, vs. a full 3" downpipe with a divorced wastegate or screamer pipe as you call it.

The result was a gain of 22 wheel horsepower from just the screamer pipe. This was done on a bone stock motor with only a cat back and an air filter + the 2 aforementioned downpipes.

Pretty big difference if you ask me.

My guess is the difference will be bugger all compared to a split dump pipe, not a open dump like you suggested.

For example, A CES dump pipe. That would have been a much better comparison.

screamer pipes are somewhat illegal, anyonet hat thinks that this noise is tops, well drive ur car to a racetrack or drag strip.  Put it on, and go for a hoon, then take it off again and drive home.  On a street car i beleive it is a stupid idea. :D

have a nice legal streetable car.  be it mostly legal.  hehe

peace out, yeahhhhhhhhhhhhhhhh

i beg to differ.

My car is a daily driver and i have a screamer on my Rb20 and dont have any problems or a rep as being a hooooon.

Its all in the way you use the right foot if you ask me as i have heard some cars down here (turbo's, V8's) that are louder than my screamer pipe :D

Beauty of living somewhere like the Apple Isle where they are pretty easy going on mods and no EPA here at the mo either :(

Cheers B

  • 7 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
×
×
  • Create New...