Jump to content
SAU Community

Recommended Posts

  • Replies 714
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Sk, Pm'd you at lunch time today...

Response sent.

Till the gallery is back and linked, following are the prices for the full kit;

Nissan Skyline

R33GTST

73175 Front Springs $144.00

83139 Rear Springs $144.00

Front Bilstein Shocks $476.00

Rear Bilstein Shocks $476.00

BNF24Z Front adj stabiliser bar $219.00

BNR11XZ Rear adj stabiliser bar $219.00

KCA331 Caster Kit $110.00

KCA348 Front Camber kit $272.00

KCA347 Rear Camber Kit $123.00

KCA349 Rear Subframe alignment kit $105.00

W0921 Bump Stop & Dust Cover X 2 $102.00

Freight Zero

Sub Total $2,390.00

Less extra 5% $119.50

Total $2,270.50

:( cheers :rant:

  • 2 weeks later...

Hey im interested in shocks alone, can you PM me with details. Im ready to buy any time if you have stock.

Interested in front and rear.

I just wondering if I should do anything else at the same time. I currently have some too low and too hard springs that came in it off the boat. I really hate them, but I dont know if that is more to do with the shocks in combination with the springs.

Am I correct in reading this will give me some height adjustability, I just think it could do with being another inch higher purely for reasons of functionality and im also sure its too low to handle well.

I havent changed shocks in a skyline before, but played around with enough other cars, so it shouldnt be a huge deal I assume? Doesnt seem to be anyone trust worthy around here.

Hey im interested in shocks alone, can you PM me with details. Im ready to buy any time if you have stock.

Interested in front and rear.

I just wondering if I should do anything else at the same time. I currently have some too low and too hard springs that came in it off the boat. I really hate them, but I dont know if that is more to do with the shocks in combination with the springs.

Am I correct in reading this will give me some height adjustability, I just think it could do with being another inch higher purely for reasons of functionality and im also sure its too low to handle well.

I havent changed shocks in a skyline before, but played around with enough other cars, so it shouldnt be a huge deal I assume? Doesnt seem to be anyone trust worthy around here.

PM sent.

:ermm: cheers :)

  • 2 weeks later...

Have just installed the bilstein kit from this group buy.

l actually look forward to getting into my car for once, as opposed to dreading the harsh ride before this awesome setup.

Garry how do you remain so patient ansewring the same questions over and over again?? ( i know i'm guilty of it :D )

All i have to say is that l am another happy customer.

Cheers Garry Thanks for everything. look forward to buying the stabilser's soon.

Have just installed the bilstein kit from this group buy.

l actually look forward to getting into my car for once, as opposed to dreading the harsh ride before this awesome setup.

Garry how do you remain so patient ansewring the same questions over and over again?? ( i know i'm guilty of it :P )

All i have to say is that l am another happy customer.

Cheers Garry Thanks for everything. look forward to buying the stabilser's soon.

What did you have installed Optimus and on what car ?

What did you have installed Optimus and on what car ?

He bought springs, shocks, caster kit and a bump stop/dust cover kit for his R33GTST.

He is saving up to buy the stabiliser bars

:) cheers :ermm:

Edited by Sydneykid
The front caster kit is a must thave, you won't believe how much a few extra degrees of caster improves the handling

Now i dont know much about suspension work, but my bushes have worn out (cracked), and its affecting my handling a bit even after wheel alignment.

Btw your pictures dont seem to work, so anychance you can fix this also please :)

Now, i got quoted at a suspension shop to fix the following:

S+F Adj Mod Rad Bush

Adj Cam Bushes

Plus wheel alignment- $610bucks.

Now i know this will replace my bushes and fix my front camber, as i think it was in negatives. Front camber should be dailed in postive to get more Go-kart response right??

Anyways what im askin is, what does your front caster kit include?? Or is this totally different??

Sorry if im askin stupid questions..

So in the near future i would like to fix these things.. AS going over 100ks the car turns left. It was ok for a few days after W/A, but now back to normal.

CHeers SK!! :ermm:

Edited by siddr20
Now i dont know much about suspension work, but my bushes have worn out (cracked), and its affecting my handling a bit even after wheel alignment.

Btw your pictures dont seem to work, so anychance you can fix this also please :)

Now, i got quoted at a suspension shop to fix the following:

S+F Adj Mod Rad Bush

Adj Cam Bushes

Plus wheel alignment- $610bucks.

Now i know this will replace my bushes and fix my front camber, as i think it was in negatives. Front camber should be dailed in postive to get more Go-kart response right??

Anyways what im askin is, what does your front caster kit include?? Or is this totally different??

Sorry if im askin stupid questions..

So in the near future i would like to fix these things.. AS going over 100ks the car turns left. It was ok for a few days after W/A, but now back to normal.

CHeers SK!! :D

The pictures don't work at the moment due to the gallery upgrade, Prank is working on that.

The caster kit enables the caster to be adjusted. Caster is the change in camber when you turn the steering wheel. Positive caster is where the outside wheel (in the turn) goes negative camber and the inside wheel goes positive camber. Skylines NEVER have enough caster, that's why they wander at speed, are reluctant to turn in and have poor steering feel. Hence the need for adjustable caster (radius rod) bushes.

The front camber kit enables adjustement of the static camber. Camber is used to keep the maimum contact pathc of the tyre to the road surface. So you need negative camber on the outside wheel (in the turn) when the chassis rolls. You don't need negative camber on the inside wheel though.

This why caster is better than camber, camber is always there even when you don't need it. Caster is only there when you do need it ie; when you turn the steering wheel.

:) cheers :P

Thanks for the helpful and informative reply SK. Learnt a lot.

Maybe if this group buy still goes till end of year, i might buy some shocks and springs of you..

I remember reading somewhere in this thread about how low the springs are set at. But now i cant seem to find it?? Think im going blind.

Atm, my fronts are 355mm, and rears are 370mm. (from centre of wheels to wheel arch)

Maybe with these shocks and springs, i can go a little lower? Hopefully the rear atleast??

Sorry i cant find your reply, where you wrote about the ride height..

Thanks for the helpful and informative reply SK. Learnt a lot.

Maybe if this group buy still goes till end of year, i might buy some shocks and springs of you..

I remember reading somewhere in this thread about how low the springs are set at. But now i cant seem to find it?? Think im going blind.

Atm, my fronts are 355mm, and rears are 370mm. (from centre of wheels to wheel arch)

Maybe with these shocks and springs, i can go a little lower? Hopefully the rear atleast??

Sorry i cant find your reply, where you wrote about the ride height..

Sorry the heights are included in the pisture which is not linked at the moment due to the gallery upgrade. Prank is working on fixing that.

The Group Buy Bilsteins have additional circlip grooves added so you can set the height you want before you fit them. There are 6 grooves 8 mm apart and I can tell you the height that you will get from each groove. Keep in mind that Skylines handle best around 355 mm front and 345 mm rear (centre of wheel to guard).

The standard circlip groove with the Whiteline springs gives ~355 mm front and ~345 mm rear. So the range of heights is ~370 mm to ~320 mm on the front and ~360 to ~310 mm on the rear.

:laugh: cheers :D

SK i PM'd you but understand u may not of got it, i am after some suspension bits which i need to purchase this week have the money ready to go when u have the bits, its all in the PM, can you reply when you get a chance thanks

adam

Hi,

Im interested in a Camber kit, can you please PM me some details of this and pricing including del to Perth :)

Thanks.

PM sent

:ermm: cheers :D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
×
×
  • Create New...