Jump to content
SAU Community

Recommended Posts

HUMMMM BIKES, yeah i have to fix mine so i can sell it. DAM IT.

On another note, i think my coils are still missing a bit at 4500 rpm, goign to do a comp test to make sure nothing wrong there.

Other then that I need $200 for a tune, anyone intrested in lending me some money. ??????

HUMMMM BIKES, yeah i have to fix mine so i can sell it. DAM IT.

On another note, i think my coils are still missing a bit at 4500 rpm, goign to do a comp test to make sure nothing wrong there.

Other then that I need $200 for a tune, anyone intrested in lending me some money. ??????

YEP BIKES :P

Both Georgie and i want to get another one by the end of this year but i cant wait that long :D

Id lend you the money old boy but i dont have it either :P

Have bought this week:

GTR projector lights

GTR front bar

GTR injectors and resistor pack

Walbro 341 fuel pump

Z32 AFM

FMIC and piping

52mm Alum radiator and thermo

Trust T518z

Rays Engineering/Nismo 17x8 + 17x9 wheels. Black finish with a polished lip.

well since the drift day i put the car in my uncles shed for a few days and done a few jobs to it besides putting it all back together.

i done the cam cover gasgets as they were spewing oil out of them. put a new seal in the thermastat housing where it was leaking with 3 bond. put some new plugs in. bosch platnums. remover the coil pack cover and made a nice aluminimu plate to hold the igniter.

i am about to pull the diff out and take the shim out that i put for the drift day as it is far to tight. it is worse than a weldy. i was going to leave it int for feb 3 but i wont be running in that so ill just put it back to normal.

New addition:

gts2tp1.jpg

If anyone doesn't know what this is, it's an R31 Skyline Silhouette GTS2, but one of only 7 made for the Tas Police.

Plans....

Within a month or so: Turbo conversion. Should double the 100rwkw output.

have 2/3's of the required parts on the way, just got my new H/D clutch this morning.

did you get this from launni?

Did a compresion Test this afternoon, on a COLD engine. I know it is suppose to be warm but couldn't do it then.

So i got

Cylinder 1 = 150 psi

Cylinder 2 = 152 psi

Cylinder 3 = 153 psi

Cylinder 4 = 151 psi

Cylinder 5 = 150 psi

Cylinder 6 = 150 psi

This was on a cold, well possibly sligtly warm engine. SO looking good.

Also got some shots inside each cylinder boore (photos), all look spot on, no leaning out spots, all thesame. Plugs looked all thesame, but cylinder one, propably a bit ritcher then any other.

So all good, new ecu seams ok. Adjusted the timing to 18 degress and will see what happens. All plugs are now 0.75mm and no missfire. YEEHHHAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA

Well after the drag day i have been busy sorying out my exhaust and intake. my new turbo manifold just arrived and im still waiting for the intake plenum to arive. also picked up a new throttle body with TPS still attached. now i just got to find a weekend when im not busy to change it all over to the new stuff. i need to upgrade my fuel system from the standard one, anybody got any suggestions?

does anyone know this car? for sale in TAS...

1655947.jpg

Before buying the RX7 I looked at that 200SX, it was a decent thing, but the body needed work.

Talking to Health who has my old 200SX he is considering selling it.

Before buying the RX7 I looked at that 200SX, it was a decent thing, but the body needed work.

Talking to Health who has my old 200SX he is considering selling it.

yeah, it would be nicer with the series 2 front though...

yeah kaaz 1.5 way diff.

he wants a 32 4 door....

wants to drift :(

ha thats funny

it must be since he seen how well my 32 4 door drifts. JK :sick:

well it should be a good car for you anyway.

are you thinking of other cars todd. you must stay focused on the mines r34 GTR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...