Jump to content
SAU Community

The Law For Modification


viet_boi
 Share

Recommended Posts

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

with neons, they have to be hidden from view, and not able to reflect off any chromed surfaces, they are also to be all of one colour, and not to flash. and linking it with the car lighting, your not allowed to have red lights displayed at the front of your car, so technically that rules out red neons. now to link it with emergancy vehicles, red/blue lights fall under police/ambulance lights, and now western power vehicles with orange lights are emergancy vehinces too(99% sure) so technically that rules out red/blue/orange, and then you are not allowed to display white light at the rear other than the reverse lights, so techincally again white, red, blue and orange are ruled out as colours for neons.

Has this changed recently?

I had red neons under mine (until the rear stopped working), and I have been pulled over a couple of times and thats what they said...that red and blue lights are reserved for emergency vehicles, although I am not sure how they could mix up undercar neons for flashing lights on a roof. Anyway, both times they took my phone number to find out for sure and let me know and I never heard from them both times. So I assumed that they were mistaken if they did bother to call the technical department.

I do know that to be legal the tubes cannot be visible to other drivers, and they cannot pulse etc as Mitchy says, but mine was connected to my light switch with an override and there wasn't any problem with that.

Link to comment
Share on other sites

I am pretty sure that for WA rims are not supposed to larger/wider than 2 inches from that stamped on the tyre plackard. So if it was stamped with 16 x 7, then you could go up to 18 x 9, but not sure really how strict they apply those rules.

...I think the standard noise level limit for exhaust is something like 92db or 98db...but there are guys out there with a lot louder, like mine is 102db and I got a mod permit for it, and there are others louder so dont know how strick they are on this.

They are however very strict on ride height. Lowest part of the body must be at least 100mm off the deck, and/or headlights minimum 500mm off the deck, whichever comes first.

In terms of other mods there seems to be big grey areas too. I have a atmo BOV that passed, the inspector just said I need a permit for it, so I got it added to the list...easy as that, where as others have said that they are illegal.  :D

rim DIAMETER can go up 2" from the largest factory option, but width follows my previous post, ie 7" max unless wider was a factory option.

Link to comment
Share on other sites

im pretty sure the rear seat windows can be as dark as u want, and only the front 2 windows and back screen need to be the 35% limit.

like a panel van or wagon can paint there rear windows (except rear glass) black if they want.

I had a (R31) wagon with 20% tint all round, when I got a sticker Warwick pits said I had to take ALL the tint off.

I had bought an R31 sedan the same day that I got the sticker (got the sticker later that night) swapped the font and rear door windows, left the rest of the tint on and went to Midland pits. The guy said it was meant to be 35% all round, and couldn't be darker, even if it was a wagon, I asked what about vans and Pano's and he said they could do it because they where classed as commercial vehicles. He still passed me though :D

The same probably goes with bikes, different rules

I would take some of the claims in the first post with come caution, seeig as they think a n external gate is a BOV... I would rather hear something from the DPI, in plain english

Link to comment
Share on other sites

the CF ...cars have to be older than 1993..that's when they change the law making Cf illegal....

pod filters have to be secured...

BOV cannot be atmospheric has to plumb back...

also FMIC cannot be water cooled...

Link to comment
Share on other sites

Atmo BOV will get passed at the pits, as long as they do not produce to much "noise"

which is totally up to the discretion of the inspector

just disengage the BOV when you go over the pits resulting it the noise coming out through the air filter all muffled

just make sure you get a permit for it

and on that note, if you have a permit mod, dont keep the original in your car as the cops have a tendancy to rip them up

Link to comment
Share on other sites

Does anyone know why you aren't allowed to have tyres wider than 9", and also why the front tyres and the rear tyres have to be the same width? As long as nothing is brushing or touching anything I can't see any reason why they are illegal, like from a safety perspective or something.

"I eated the purple berries... they taste like burning!"

Link to comment
Share on other sites

Because they said so...

yeah pretty much hey

my rims are 7 1/2 inches

is f**ken annoying

keep having to borrow stockies when i get a yellow

dont think the offset really helps me any either

apparently you are only allowed to increase the Track of your car by 25mm which is stuff all

my rims increase my track by like 2 inches if not more

Link to comment
Share on other sites

Ok, so some of you may think I am speaking shit, cos what I am about to say will fly in the face of what some people have posted here, meh.

I just had my rego transferred from SA to WA, the following were found to be legal

17.10 inch rims rear, 17x9 front, both were measured - the only thing the inspector commented on was the width of the tyre - had to be correct for the rim (they are slightly stretched, so he checked), he also checked the track, as I have widebody rear and pumped front guards. He also pointed out I had some rubbing under the rear, I told him that is why I got the adjustable rear camber arms and he was happy.

They will not give a permit for exhausts or suspension. I had coilovers and adjustable arms fitted, no problems, but he also wouldnt give me permits for them - he said 'they are either legal or not' Same for my wheels.

Car legal exhaust is 90db, MC its like 98 or 100 or something, but louder than car, truck is also louder than car.

Guages can be fitted to the A pillar, but must be fitted in a manner that they will come off if you hit your head on them, or out of head impact range.

I also got permits for Bride seats, centre gauges, steering wheel and handbrake cover. He didnt bother giving me one for the shift knob. I also got permits for intercooler and piping, manifold, catch can, front and rear strut braces and pod - basically all the aftermarket looking bits.

Hope that helps

He (the inspector) said he doesnt normally give permits for pods (or exhausts :) ) anymore, but as a couple of guys had been through recently with defects for pods, so I got one off him for it (he was also bitching about cops defecting cars who didnt know what they were doing.

I was also told pre 1996 cars can have c/f or fibre glass bonnets, as they predate ADR front end crash test requirements. vents are ok, as long as they have mesh (to stop fingers). The bonnet must also have a double latching system (as the factory one does).

Do yourselves a favour, if you have mods, get permits, its pretty easy, and I found the guys very reasonable. Its cheaper to spend $30 for a mod permit, than it is for a full inspection. (can save heaps of dramas too)

Oh, and I laminated my permits too :P

I love it over here, in SA, a car has to be practically completely factory to pass, including ride height.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Any chance you can get a Nistune board installed instead and set the speed limit to whatever your tires can handle?
    • Hi all, I need to get this HKS SLD attached to my stock ECU because I've now got the German autobahn and faster European circuits to contend with.  The car is a manual 2dr ER34 with an AT ECU and I've realised the AT ECU has two pins for speed sensor signals: Pin 29: Vehicle speed sensor signal (Vehicle speed sensor 2) Pin *58: Output shaft rotation sensor signal (Vehicle speed sensor 1) - *RB25DET A/T model only Before I go butchering this harness, is anyone sure of which pin is the correct one for signal adjustment? The attached document from HKS indicates pin 29 but I found this situation mentioned in the following thread on a different forum (R34 GTT Auto Trans Speed Cut Problem | Zerotohundred) mentioning pin 58 needing to be altered by member zephuros, albeit it seems to be for an RSM-GP and the info appears to be old.  R34_All_Workshop_Manual-pages-2.pdf R34_All_Workshop_Manual-pages-3.pdf R34_All_Workshop_Manual-pages-1.pdf HKS SLD Vehicle Pin out P59-P70 ER34-pages.pdf
    • Slimline sub on the rear parcel shelf is doable. Pioneer TS-WX140DA is only 70mm high.   
    • People like Johnny Dose Bro might be laughing at my post because I accidentally added 100mm to my numbers. 350-355 is indeed the lower limit. 450 is off-road Skyline spec.
    • What is the "compromise" that you think will happen? Are you thinking that something will get damaged? The only things you have to be concerned about with spherical jointed suspension arms are; Arguments with the constabulary wrt their legality (they are likely to be illegal for road use without an engineering certificatation, and that may not be possible to obtain). A lot more NVH transmitted through to the passengers (which is hardly a concern for those with a preference for good handling, anyway). Greatly increased inspection and maintenance requirements (see above points, both).   It is extremely necessary to ask what car you are talking about. Your discussion on strut tops, for example, would be completely wrong for an R chassis, but be correct for an S chassis. R32s have specific problems that R33/4 do not have. Etc. I have hardened rubber bushes on upper rear control arms and traction rods. Adjustable length so as to be able to set both camber and bump steer. You cannot contemplate doing just the control arms and not the traction arms. And whatever bushing you have in one you should have in the other so that they have similar characteristics. Otherwise you can get increased oddness of behaviour as one bushing flexes and the other doesn't, changing the alignment between them. I have stock lower rear arms with urethane bushes. I may make changes here, these are are driven by the R32's geometry problems, so I won't discuss them here unless it proves necessary. I have spherical joints in the front caster rods. I have experienced absolutely no negatives and only positives from doing so. They are massively better than any other option. I have sphericals in the FUCAs, but this is driven largely by the (again) R32 specific problems with the motion of those arms. I just have to deal with the increased maintenance required. Given how much better the front end behaves with the sphericals in there.....I'd probably be tempted to go away from my preference (which is not to have sphericals on a road car, for 2 of the 3 reasons in the bulleted list above), just to gain those improvements. And so my preference for not using sphericals (in general) on a road car should be obvious. I use them judiciously, though, as required to solve particular problems.
×
×
  • Create New...