Jump to content
SAU Community

Recommended Posts

hey, my one of my headlights looks like it is turning a yellowish sorta colour., but its on the inside, right now its not very noticable, but it is slowly expanding....

anyone know how i can stop this thing from spreading? and how to remove whats already there?

thanks

Link to comment
https://www.sau.com.au/forums/topic/99826-r34-gtt-headlights/
Share on other sites

hmm... i remember someone ages ago with a 33 taking the headlights off and putting the plastic into some sort of solution which cleared it up like nothing else... i think it might be a matter of taking the clear plastic off and cleaning it with something.

tried running a search through these forums for something related to this?

mine did it too. i had to take my light apart and clean the inside. It was ball breaking, but my car looks brand new now. well worth the hastled, just make sure you set a whole day aside.

i unbolted the light. and separated the clear plastic from the rest of the light assembly using a hairdryer. cleaned the inside of the plastic using brasso (which works Shmiko by the way even on the outside). Then resealed it using windscreen silicon just incase i ever have to do it again.

mine arent that bad, so far its only the top section, ie eyelids for the lights would hid it,

i will buy some of that product and use it this weekend

thanks everyone for your help

mine did it too. i had to take my light apart and clean the inside.  It was ball breaking, but my car looks brand new now. well worth the hastled, just make sure you set a whole day aside.

i unbolted the light. and separated the clear plastic from the rest of the light assembly using a hairdryer. cleaned the inside of the plastic using brasso (which works Shmiko by the way even on the outside). Then resealed it using windscreen silicon just incase i ever have to do it again.

Any cance of you running me through pulling the light apart? My drivers side light is completly fogged and I didnt want to damage it while taking it apart.

cheers

do repco and supercheap etc sell this plastx stuff or is it a special stuff from elsewherre

It should be readily available from autobarn. I looked in a few supercheaps but they've had to order it in. Ive had my car 18 months and the one bottle is still going cos you dont use much at a time.

Any cance of you running me through pulling the light apart? My drivers side light is completly fogged and I didnt want to damage it while taking it apart.

cheers

1)the front bar needs to come off to ge to the two bolts underneath the light.

2)Once that is done their are about 5 bolts holding the light in. Unlbolt them disconnect all the electric cabling powering the headlights.

3)remove metal pins holing clear plastic cover on then use a hair dryer set on hot hold it 15cm away from plastic

4) slowly pull the light apart prying it carfeully with a spatula(same as one you would use when filling cracks before painting a wall)

5)clean clear plastic using brasso. rub on let it dry and polish. wash out iwth water

6)once it is apart clean out all the black silicon from the section where the plastic sits inside the black surround so when you glue it together again it bonds properly.

7)put small amount of windscreen silicon into area which you have cleaned out and put clear light cover back on push together and replace metal clips. i suggest letting it sit for as long as possible then puttig it back on say at least 6 hrs later.

Hope that helps. it isnt really that hard just time consuming.

please note. some r34 gtt's have had the oem xenon kit cut out of the bottom. if this is the case with yours make sure you cover the section that has been cut and glued back with the windscreen silicon and let dry. This can let moisture in and discolour the clear plastic.

1)the front bar needs to come off to ge to the two bolts underneath the light.

2)Once that is done their are about 5 bolts holding the light in. Unlbolt them disconnect all the electric cabling powering the headlights.

3)remove metal pins holing clear plastic cover on then use a hair dryer set on hot hold it 15cm away from plastic

4) slowly pull the light apart prying it carfeully with a spatula(same as one you would use when filling cracks before painting a wall)

5)clean clear plastic using brasso. rub on let it dry and polish. wash out iwth water

6)once it is apart clean out all the black silicon from the section where the plastic sits inside the black surround so when you glue it together again it bonds properly.

7)put small amount of windscreen silicon into area which you have cleaned out and put clear light cover back on push together and replace metal clips. i suggest letting it sit for as long as possible then puttig it back on say at least 6 hrs later.

Hope that helps. it isnt really that hard just time consuming.

please note. some r34 gtt's have had the oem xenon kit cut out of the bottom. if this is the case with yours make sure you cover the section that has been cut and glued back with the windscreen silicon and let dry. This can let moisture in and discolour the clear plastic.

Thanks mate ill do that

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...