Jump to content
SAU Community

Stagea Manual Conversion Guide

tRUkbOY
 Share

Recommended Posts

Stick180 Enthusiast

Stick180

Posted
Posted

Sorry for the thread bump, but i need some info, ive read through this post, but couldnt find what i was after.

Im wanting to convert my S2 C34 RWD, will i be able to use a 33 tailshaft? or will i have to do a cut n shut ?

  • Replies 290
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Duncan
Duncan

awesome, enjoy it. mine's been manual for almost 10 years now and it's still great fun

KiwiRS4T
KiwiRS4T

If you don't get a reply just google "electronic speedometer drive for R32 gearbox" or something like that . As for wiring apart from the speed signal which is obvious there is just the reverse ligh

KiwiRS4T
KiwiRS4T

Make sure you get an awd box! Top up fluids and bleed - nothing special to do.

Posted Images

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Sorry for the thread bump, but i need some info, ive read through this post, but couldnt find what i was after.

Im wanting to convert my S2 C34 RWD, will i be able to use a 33 tailshaft? or will i have to do a cut n shut ?

What gearbox are you using? You may be able to use the shaft you have. (Don't know for sure as mine was AWD to GTR AWD).

  • 2 months later...
  • 1 month later...
fmlycar Proficient

fmlycar

Posted
Posted

I have a issue with my s1 rs4v that's been converted to manual. Awd has never seemed to function right. What's the process of fault finding something like this? Pump primes on start and had been bled. Where would the attesa ecu be to check for fault codes?

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

I have a question mates,i have a Auto AWD R34 with Rb25 DET neo and want to go with a manual box.My question is what do i have to do to get my attesa working like normal?

Make sure you get an awd box!

Top up fluids and bleed - nothing special to do.

  • Like 1
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

I have a issue with my s1 rs4v that's been converted to manual. Awd has never seemed to function right. What's the process of fault finding something like this? Pump primes on start and had been bled. Where would the attesa ecu be to check for fault codes?

Left hand side of boot forward of wheel arch.

  • Like 1
fmlycar Proficient

fmlycar

Posted
Posted (edited)

Is there anything else that would stop the attesa working without showing a light in the dash?

Just to note I'm using a r34 gtt power fc if that makes any difference

Edited by fmlycar
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Is there anything else that would stop the attesa working without showing a light in the dash?

Just to note I'm using a r34 gtt power fc if that makes any difference

Has it ever worked since you had it? New ECU requires a line from the TPS to somewhere - there's info in here somewhere.

  • 2 weeks later...
fmlycar Proficient

fmlycar

Posted
Posted

Does anyone have a pic of where the atessa ecu is in a s1 c34? And how much interior trim do I have to remove to get to it?

I have one of those electronic torque split controllers fitted (been in the car since I e owned it) and if I turn it up above say 2, the 4wd and abs lights come on. Is that a normal function due to the way they are wired in? I know it does it switching from 4wd to 2wd.

Really want 4wd for launches. Probably break drive shafts but I have spares.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

As above he attessa ecu is behind the trim between the LH wheel arch and the back seat. I would not be confident that the torque split controller can safely put you into 2wd. If you read the instructions for putting the R33 (and C34 Stagea) into 2wd I would doubt that a torque controller could do that. R32 is another story.

fmlycar Proficient

fmlycar

Posted
Posted (edited)

Got me stuffed where the attessa ecu is. Pull my trim apart today and couldn't find it it front or behind the strut tower. Do I need to remove the back seat or something? Can I just plug in consult and see if anything shows up? Even though I'm running a power fc?

Pump primes on start up and every now and then sitting at idle I hear it come on for a moment and then off again

Edited by fmlycar
  • 1 month later...
melvin025 Rookie

melvin025

Posted
Posted

Apologies for the thread bump but I'm at a loss, does the clutch pedal have to be modified to fit? I have a r34 pedal but it's fouling on the bracket for the footbrake. It also doesn't line up with the hole at the top where the footbrake. Was just wondering if anyone had any photos of how they mounted theirs

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Apologies for the thread bump but I'm at a loss, does the clutch pedal have to be modified to fit? I have a r34 pedal but it's fouling on the bracket for the footbrake. It also doesn't line up with the hole at the top where the footbrake. Was just wondering if anyone had any photos of how they mounted theirs

Go back to the beginning of the thread and Trukboy explains it pretty well.

melvin025 Rookie

melvin025

Posted
Posted

I wasn't planning on using the footbrake I've already got my handbrake installed but I'm needing a bit of guidance with the clutch pedal. Has no one got any photos? I see that Trukboy got a recessed master cylinder, is it possible to do it with a standard master cylinder? I bought a job lot of bits off someone with a gts4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      S1 rb25/s14 starting problem

      By Dose Pipe Sutututu · Posted

      When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...