Jump to content
SAU Community

Recommended Posts

Yeah i know its cheap for what it has in it, blu-ray players are $1500 alone in the shops. But for a mass produced unit i just think they could have sold it for a bit cheaper, as they will no doubt make MASSIVE profits off the software to re-gain the hardware losses.

The hd-dvd addon drive for 360 is $250.. for essentially the same quality. Blu-ray being included in the price of the ps3 is no special bargain.

  • Replies 459
  • Created
  • Last Reply

Top Posters In This Topic

haha ok thanks for the info.

Just an update, I have paid off my PS3 pre-order in full. I got EB to price match the ToysRUs pre-order deal as they were more then happy to do it.

So I got the PS3 + Resistance Fall of Man + Motorstorm and 50% off another game for $1099

Being a VIP member at EB I also got $30 off Tony Hawk

All up it cost me under $1400 for my pre-order which is the following

PS3

Motorstorm

Resistance Fall Of Man

Tony Hawk

F1 CE

Ridge Racer 7

I haven't head anything about the Australian version being cutdown. I have also just done some research to see if I could find anything but alas I turned up nothing. Can you point in the right direction on where you found this info?

i wouldn't waste your time with F1, it's subpar as have been f1 games for some years now.

Also if we are going to do the debate of hd costing 250 on the 360 also throw in the fact wireless for the 360 is 169.95.

The 360 is great, the ps3 will be great, not one title on launch is a system seller. As is with every new console almost, which i have pointed out before.

by the sounds of your job hanyou we may be talking to each other as well!

nobody by the looks of things... :P price is too high for joe consumer for a while.. including me..

The launch of Sony's PlayStation 3 games console got off to a feeble start last night last night with officials, media and security outnumbering customers for most of the evening.

Over 500 retailers around the country threw open their doors as the clock struck 12:00am, expecting the frenzy that accompanied the games console's overseas debuts.

But most stores were virtually deserted, despite the 20,000 pre-orders Sony said it had received.

Even at the official launch event held at Myer's Pitt Street store in Sydney's CBD and attended by Sony's local managing director, Michael Ephraim, media and security outnumbered PS3 fans until at least 11:00pm.

At midnight, about 40 PS3 buyers had arrived to collect their consoles, causing distress for the army of camera crews who turned up expecting to capture launch mayhem.

Desperate producers unashamedly asked the crowd to fake excitement when the cameras were rolling, while a team from 2Day FM let out bogus cheers to convince their radio listeners that a launch extravaganza was underway.

The scene was a stark contrast to the US launch in November last year, where one man was shot by thieves and fights broke out over limited stock.

yeah well I guess considering people like me who bought one 5 months ago at the real launch would have lost interest by now, and everyone else would be sick of hearing wankers like me banging on about how they got their PS3 in early november!! lol

big mistake by sony to no release it simultaneously with the rest of the world. it's certain to have pissed people off who feel they are no longer buying some special, brand new, latest console. 5 months ago it was the shit. now it's just another console (albeit a damn good one).

I wouldn't mind one.. but $999 is a lot when there aren't a heap of games to choose from right away.. I will probably wait 12 months until there are a few more games to choose from.

I think the price here is about $109 for most games - why would anybody buy games locally when you can import them for about $75 thanks to a high aussie dollar?? Sony is strange sometimes.

^^^

well almost every console in the world is released here later than oversea's so i don't see how that would of made a difference at all.

PSX was launched in 94 in japan, 95 in australia, ps2 was released march 2000 japan, and october 2000 in australia,

gamecube was launched september off the top of my head in japan and march the following year here,

psp was launched in november in japan and mid the next year over here.

So i don't see where you are going with that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...