Jump to content
SAU Community

Recommended Posts

I have r33gtr wheels on my s13.

I am looking at buying some R rubber in the near future.

I like the look and the reports i have read about the re55's.

My main concern is that i currently have a 225 street tyre fitted and it has left me with next to no clearance on the suspension, thats with a 30mm bolt on spacer. i think i should be able to fit the 235 40 17 that the re55's are made in, i am just concerned that the width (235) is a little narrow for a 9 inch wide wheel. i wouldn't want the tyre to pop off the rim under hard cornering etc.

also does anyone know of an R rubber tyre that comes in 225 40 17, and if that would be ok on a 9 inch wide wheel?

i really like these wheels and would like to use them as my track day wheels, obviously this will only happen if i can get a tyre combo that will fit and be safe.

Link to comment
https://www.sau.com.au/forums/topic/131992-tyre-widths-for-9-inch-wheels/
Share on other sites

i am just concerned that the width (235) is a little narrow for a 9 inch wide wheel. i wouldn't want the tyre to pop off the rim under hard cornering etc.

Well my 215/45s have not popped off after grip track days, smashing the wheel on a gutter or

light easterly breezes, so I think you will have no problems, but no, nobody makes a 225/40R17 R-tyre

I have looked :P

IMG_0365.jpg

p.s. I have lowered my car since this pic so don't worry...

p.p.s Does anybody search at all?

235/45 on 17x9

IMG_0368.jpg

215/45 on 17x9

IMG_0366.jpg

QUOTE:Well my 215/45s have not popped off after grip track days, smashing the wheel on a gutter or

light easterly breezes, so I think you will have no problems, but no, nobody makes a 225/40R17 R-tyre

I have looked

i understand normal road tyres will stay put on the wheels, even when given a hard time, i was more concerned that r rubber usually has a very stiff side wall and it may tend to be less happy to stretch onto a wider than suited wheel.

thanks for the reply.

i did searh, but found it hard to narrow down what i wanted to know, so search results were very broad.

if anyone knows of an R rubber tyre that is made in 225/40R17 please point me in the right direction.

Edited by R32gts-t

Personally i wouldnt run anything less than a 245 on a 9" rim in R compound and especially with RE55's, the bridgies tend to have much stiffer side walls than most semi slicks anyway, so not only will the tyre fitter have a massively hard time getting them on (if at all) but i'd say you'll have alot of trouble with ride quality and will have to run higher pressures to stop them getting nudged off the bead..

i understand normal road tyres will stay put on the wheels, even when given a hard time, i was more concerned that r rubber usually has a very stiff side wall and it may tend to be less happy to stretch onto a wider than suited wheel.

Well I am running Dunlop Z1 tyres (top pic) they aren't what I call normal road rubber they are not D01Js but they are not Korean Tempe tyre specials either.

What you find with tyres is that they seem to mould to the wheels, I was recently trying to put some 225/45 onto a 9" wheel after having spend god knows how long on a 7.5" wheel and it was just not happening.

But when I took my Z1 tyres off the wheel I destroyed (they retained pressure after the incident) they had changed shape to suit the 9" wheel... Mounting a second time required no special techniques whatsoever.

The only real problem you will have is that nobody will either know how to or be willing to put them on for you.

I would be really interested to know the circumstances of anyone having sealing problems, the only person I know who has runs second hand Commodore tyres 235 which have spent ages on an 8-inch rim then sticks them on his 10.5 (IIRC) which is a larger stretch the 215/45 on 9-inch.

Interesting how everone is an expert on the consequences of something that nobody ever does :ninja:

At the moment i have 235/40-18s on 10.5" rears and 225/40-18s on 9.5 fronts. Only reason i have this is because fitting 10.5" rims on the back of a gtst is nearly impossible with just rolled guards. If i used bigger than 235s then the tyres will hit on the guard and also stickout past the guard. The person that had the car before i bought it has been using this size tyre for 2yrs and i have been for a yr without any problems from damage or the police.

i just found out that toyo proxes r888 come in a 225 45 17

how do they compare with the bridgestone re55's does anyone know?

alternatively i am going to try and squeeze some 235 40 17's on.

Edited by R32gts-t

Hi Duncan , what offset 17x8's did that R33 GTST have ? I have Rays 17x8.5 30P and plan to fit 235 45's when these noisy G grids wear out .

Also though slightly O/T , if R33 GTR's had 245 45 17's on the back how did Nissan correct the speedo error compared to 33 GTST's std rolling diametre if the diff ratio and speedo gear is the same ?

Cheers A .

Okay then, similar question...Does anyone know the maximum tyre width that will fit onto an 18x8" rim?

I'm presently running 235/40 R18 on 350Z Track rims, but would like to go a bit wider on the rear next time around...

245's would seem logical as the Z already comes with these - but the problem is that to get the correct rolling diameter for an R33 I'd have to get 245/35 R18s (-0.5% different diameter to standard)....a bit of an unusual size apparently...the only tyre manufacturer online I could find that lists them at a semi-reasonable price is Kumho with their KU19 (I had bad experiences in the past with these too)

...Now if I could squeeze a set of 255/35 R18s (+0.60% different diameter to standard) onto the back that would be a lot easier as they seem to be readily available.

...but:

a) would it be possible & safe?

b) would it look terrible (bulging outwards etc)?

Any insight would be appreciated!

Not pushing it at all...depends on the brand of tyre.

Toyo specifes that their Proxes 275s will fit on a 9inch rim. You just need to do the homework.

I just put a couple of pirelli P ZEROs 285/30/18 on the back of my GTS-T, which is on a 9" rim.

Okay then, similar question...Does anyone know the maximum tyre width that will fit onto an 18x8" rim?

I'm presently running 235/40 R18 on 350Z Track rims, but would like to go a bit wider on the rear next time around...

245's would seem logical as the Z already comes with these - but the problem is that to get the correct rolling diameter for an R33 I'd have to get 245/35 R18s (-0.5% different diameter to standard)....a bit of an unusual size apparently...the only tyre manufacturer online I could find that lists them at a semi-reasonable price is Kumho with their KU19 (I had bad experiences in the past with these too)

...Now if I could squeeze a set of 255/35 R18s (+0.60% different diameter to standard) onto the back that would be a lot easier as they seem to be readily available.

...but:

a) would it be possible & safe?

b) would it look terrible (bulging outwards etc)?

Any insight would be appreciated!

A 255 would fit easy. might come out a touch good protection for ur rims lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...