Jump to content
SAU Community

Recommended Posts

I have purchased a Sliding Performance RB25 hiflow for RB20 and will be installing it on my RB20det over the weekend and thought as there was no results on them with RB20det's I will post all my results here.

The turbo arrived as soon as Aaron promised and my first opinions are it is a good quality product. The machining and finish is very high quality and the CHRA came filled with fully synthetic oil. Both the compressor and turbine are new as well as the whole shaft, bearings and carteridge.

Here are some photos.

100_1180.jpg

100_1179.jpg

100_1178.jpg

100_1177.jpg

100_1176.jpg

100_1175.jpg

100_1174.jpg

100_1173.jpg

The turbo will be going on a mildly modified RB20det with approx 100,000K's and the following

RB20 turbo wastegate

BOS importing split dump/front pipe

3" meatalcat

2.75" kakimoto JASMA approved catback (will be upgrading to 3" later)

TRUST tube and fin FMIC

GTR 444cc injectors

GTR fuel pump

Remapped factory ECU

pneumatic/mechanical turbotech boost controller

NGK copper plugs gapped to 0.9 (factory coils still in good condition)

Stock cams, airbox, BOV, panel filter.

Other modifications to come will also be 1.5 way mechanical diff and brass button clutch.

I will not have a chance to dyno the car and make adjustments to the timing and fuel map untill next Thursday but will post the results once done. currently I estimate the car is making around 140RWKW. I am hoping for 210RWKW once installed.

Will keep you all posted :(

Cheers

  • Replies 231
  • Created
  • Last Reply

Top Posters In This Topic

yeah it's funny. I think it is because the snout is tapered it actually looks a lot more bored than it actually is. There is a good bit of meat left on the snout. it just looks super thin in the photos :(

I may have ot re estimate my initial power estimate after calculating the flow of the 2.75" exhaust compared to a 3". I worked out it will flow 19% less than a 3"

If I am wrong please feel free to correct me. but I think it will be a fairly large restriction and I will not have the time or money to replace it untill after the dyno is done.

but we will see how it goes.

Edited by CEF11E

I think you will reach 200rwkws (all depends on the boost you run I guess) with all the mods you have said. You will need to sort out your ecu as you menioned and once thats done I dont see why you cant get what you want even with the 2.75 " exuast. Anymore than about 200-210rwkws you will need to add a z32 as the stock afm will be running out of resolution.

I have the very same turbo, and am equally impressed with the finish and quality of the product.

I just installed it on my RB20 with similar mods but stock ecu. Suppose to be getting a dyno and remap tomorrow but this isnt happening now, so im going to run a remap ecu from a similar turbo until i can get to a dyno.

its pretty laggy on a stock ECU map i can say that much!`

I'm very interested in doing this turbo thing too. Also got a cef, so quite eager to see the results.

Without trying to hi-jack the thread, what do you call 'pretty laggy' simon?

haha arent all rb20's laggy. I had a 2530 on mine in the old sil80 and damn it felt laggy in comparison to a mates sr with a 2530. Pissed me off cause i hate sr's. RB's FOREVER :)

Im guessing full boost by about 4500??

lol, mine hopefully is being milled up today :P

hope to get it installed onto the Stagea within the next few weeks, but we'll have to see what I can get organised - healing from the patellectomy so cant drive for a while yet. :laugh:

Not sure about the oil feed yet. I am going to take mine off first thing saturday morning and head over to pirtek with it and the 2 banjo bolts. will either get a nre braided one made up or mod mine to suit. The banjo bolts have to be drilled out to 6mm and the banjo fittings need to be drilled out to 5mm.

I do have the tools but would rather a pro did it. :laugh:

Interesting to hear about your braided line pricing/specs if you go for that option :)

I want a new turbo too - but dam the delay from Sliding :D:P :P

Just grab another turbo, I have a spare waiting for the hi-flo treatment. Perfect working order, swapped a set of stock R33 wheels for it ;)

wasnt able to get to the dyno today, so i had Jeff from The Speed Lab put my cefiro remap that was suited to the KKR 430 onto my r32, while not perfect its still better then running the stock map with this turbo.

the ceffy remap was tuned for 16-17 psi, but for safety until i get the car onto the duyno, im running 1 bar.

Im getting full boost at over 4000 rpm but before 4500. from then on it pulls extremally hard,

Comparing to my cefiro, which had 200 rwkw, this feels slightly quicker.

The downside is that offboost and while its trying to build boost down low in the rpm range its bloody slow lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to it's full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so damn hot in there, that made it all the more easy to remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. I was standing there looking at the car and said 'f**k it'. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...