Jump to content
SAU Community

Kws At The Wheels  

219 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

  • Replies 152
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

"You cant just jump in the ring with Ali caus u think ur box. Hey he knows i can box. So check it, if i lose the winner takes my car clean and clear. But if i win, i take cash, and i take the respect."

R32 GTST, usual mods, stock turbo 170RWKW @ 14 psi

Edited by R32Abuser
".....so check it, if i lose the winner takes my car clean and clear. But if i win, i take cash, and i take the respect."
Stuff the respect I'm here for the chicks!

R33 GTS-T (manual-auto) 203rwkw @ 13.5psi from Boostworx.

that would be SLO-031

my best was 177 my worst was 154 i dont know why it lost power from one run to another but i know it hasnt stayed lost just cant afford to go on a dyno every other week

i remember i was in my silo when this bloke pulled up next to me, i was like ohh ok, then BANG 100 meter

wheelspin :O

i saw his plates "slo-031" i was like :dry::O:O:O:O:O:O

My lil' 66 skyline is doing 140 at the treads, but with the new bits ( turbo, zorst and a couple of other things) I am hoping for 180kw at the treads ( I want to be australia's most powerful 6 cyl Prince Skyline GT-B) not that I am not already... hehe :dry:

Edited by 66 skyline gt

Hey ,

my GTR was tuned at 262 rwkw at a bar,

now with more boost and electronic controller prob pushing 280 +

but its a GTR so all the power transfers to the ground and the magnesium wheels being light it makes it more responsive

mike

^^^ GT42R infact

last made 378kw on street tune

apparently having a 2spd powerglide put behind it

lol my bad.. GT42r... Lunatic. :)

Yep a powerglide is going in behind it as the r33 auto built up had issues holding the power. Not surprisingly really as 373rwkw is a rather large amount of power. :)

geebus! some of yous have some serious power! i'm shitting myself in my little 80kw mx6 turbo around corners (that is with a blown head and running at 2psi hahahaa) and some of yous are hitting 300kw mark! damnnnnnnn

lol my bad.. GT42r... Lunatic. :)

Yep a powerglide is going in behind it as the r33 auto built up had issues holding the power. Not surprisingly really as 373rwkw is a rather large amount of power. :)

Back that up with having issues trying to get it into reverse when required .... :laugh:

Looked good on the Smasa Cruise. I think that's how you spell it :kiss:

153.1kw @ 11psi via Boostworx

Stock Turbo, 3 inch exhaust, crappy cooler, ..errr....fuel pump & Air Filter

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...