Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

Hi Guys,

Long time reader first time poster. I have been doing some digging around into acts and legislations. The document that everyone seems to recommed is the EPA 2006 Modification guide which isn't actually a legal document but just a guide.

The Legislation the guide is 'suppose to follow' is the Environment Protection (Vehicle Emissions) Regulations 2003 which can be found here http://www.legislation.vic.gov.au (choose the 'E' and choose Legislation and go down to 60)

the PDF link I have added

http://www.legislation.vic.gov.au/Domino/Web_Notes/LDMS/LTObject_Store/LTObjSt4.nsf/DDE300B846EED9C7CA257616000A3571/AD52E1CA8ECA6916CA2577610035F8CA/$FILE/03-10sr010.pdf

This is what laws EPA Victoria have and what all EPA testers must abide by.

Yes the document has the typical legal layout (which is painful to read) but from reading it and going over it with others. Most of what is in the EPA 2006 Modification guide isn't actually in the legislation it is suppose to follow. Please correct me if I'm wrong but if there is another Act or Legislation I have missed please include it.

There are so many points I can make about who and what has been deemed non-epa compliated but yet is not in there legislation. I know EPA is a VERY touchy issue but I am putting this out there hoping it could make a difference and help inform people what is the law.

Yes I have been playing to much Deus Ex: Human Revolution and think the EPA are evil conspiracists controlled by the Greens which control the Labor Government.

Well the few things i checked.

- Exhaust noise

- Vehicle Emission controls (which covers ECU, PCV etc)

Were the same in the Guidelines, and Stat Rules. And that is what 99% of people here are going to be pinned for ;)

Also the part you have referenced is simply the emissions part for Victoria dont forget. There is more too it like:

Road Safety (Vehicles) Regulations 2009

That one also makes reference to ADR's and other things about emissions etc. I really CBFd trolling through it to see exactly what is referenced but my guess would probably say enough to make it a headache to then go and check each ADR.

  • 1 month later...

Hi Guys,

Just my luck i recieved a Noise Test request from the EPA. Thank god its not a full epa since im running a topmount with the rb30 inside. But i just wanted to be 100% sure, is the simple process of just showing up to a tester, getting it tested then giving the Certificate of Compliance to the EPA? No need to show the car?

Also, should i be worried about chucking the OEM r34 GTT exhaust back on with the amount of modifications i have done to the engine? (eg, gt35r, rb26/30, custom vband dump, ect) no chance of me damading the engine due to back pressure right? Obviously i wont be on WOT but what about the actual test at 4800rpm?

Where are they sending you for the test?

As i have said previously a mates GTR got done for noise, pod filters and a boost controller and the tester said if the car isn't stock its going to the EPA. He wanted stock Nissan cat or an EPA approved import cat with paperwork to prove it complied, stock FPR, stock exhaust, stock FMIC etc

Any "lenient" testers you recommend nismoid?

Although i have to replace my whole exhaust system, i just dont want any further issues with anything else. If thats even possible.

BTW ive been thinking about a racepace exhaust, do you recall what the ball park price they charge?

Been calling them 2 times a day for the last 2-3days but no one ever picks up or even returns my calls =[

No such thing as lenient either it's under or it's not

sorry alex let me be more spesific,

I dont want to draw attention to the fact that im running semi slicks, a top mount turbo ect, A noise tester wouldnt be concerned about this stuff right? Nor should he ask to see the engine?

Sorry mate, just saw your in Melbourne. If you were in Sydney i would say prepare the vaso as regardless of what they catch you for they rape you for everything up here, but Melbourne may be a bit different

Gosh man that must be a nightmare.

When i got home from work and opened up the mailbox to see a envelope from EPA . . . . my heart sunk and i was preparing for the worst. A full engine rip out and buying a new rb25 to put back in. To my relief it was just a noise test. I dont know how much longer i can go driving a car like this lol.

sorry alex let me be more spesific,

I dont want to draw attention to the fact that im running semi slicks, a top mount turbo ect, A noise tester wouldnt be concerned about this stuff right? Nor should he ask to see the engine?

They are testing for noise as i said.

That is all they care about.

go to exhaust city in chelt. great guy for epa noise testing. epa noise testers dont give a shit what your car looks like as long as it pasts test your fine. then you fax it through to epa and your cleared

I had an EPA for noisy exhuast on a VN (had a note through the mail saying the jacks had reported it), I took it to the local RACV place & he failed it so I made some restrictors & went back.

He told me he suspected that restrictors had been installed and threatened to report it to the EPA.

I took it somewhere else & they passed it no probs.

All they do is stick a microphone behind the exhause (they have measuring sticks to make sure it's in the right place), give it a couple of revs and that's it.

As said before, they don't care about anything else on the vehicle, just the noise level, think it's like 90dBA

As for roadies i's getting really hard to get one now because they have to take pictures.

Used to get them all day long up lol

When I bought my R33 they stung me for tint on the door too dark, new windscreen as the one on it was "sandblasted" & front brake discs.

Taking the tint off was fun (not).

  • 1 month later...

I just think its BS how this state/ country doesn't allow you to modify your own vehicle how you want. Not allowed 2 intake mods wtf?? not allowed this not allowed that... what if your car is 10 times safer than standard form then what??

As sad and stupid the laws are im still going ahead with my custom setup. Just puts a downer on it after reading a few posts about it all.

I wish there was good reasons behind not allowing after market modifications. :(

I just think its BS how this state/ country doesn't allow you to modify your own vehicle how you want. Not allowed 2 intake mods wtf?? not allowed this not allowed that... what if your car is 10 times safer than standard form then what??

As sad and stupid the laws are im still going ahead with my custom setup. Just puts a downer on it after reading a few posts about it all.

I wish there was good reasons behind not allowing after market modifications. :(

I think because of the following reasons:

1. Cars have safety features which you can affect by modifying. (Airbags, seatbelts, crumple zones, etc. etc.) Just think about that fully sick 5" monster tacho you see on some dash's. Then picture said tacho hitting the driver in the head when their whole body is flung forward because they rear ended someone.

2. Cars have pollution equipment in place to minimise how much nasty stuff you inhale when your mate drives off. CATs are fitted for a reason. Cars are tuned for pollution minimisation. etc.

3. Modifications done by back yarders can be dangerous as they haven't got full knowledge of engineering principles and the ADR's.

4. Putting modifications to driveline components (such as fully sik 22" chrome bling wheels) means other components wear out faster as increased loads contribute to extra stresses on the system. Again, your average backyarder (and some mechanics for that matter) have no idea when it comes to 'system engineering'. Hence why we have to use an automotive engineer for drastic and not so drastic changes.

I guess to sympathise with you about 2 intake mods.... Agreed, the EPA are a bunch of idiots. They should be educating car enthusiasts on how to get the most performance and fuel economy, but minimal impact on the environment. Don't get me started on Vicroads. Those guys have no idea what so ever. They brought in some rules to say cages weren't allowed to be fitted to cars (at all) because it affected crumple zones etc. Pity that means older cars (say pre 90's) which may not have crumple zones now could not have a cage if you wanted to drive it on the road. Fortunately they have reversed their decision. Twits!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
×
×
  • Create New...