Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...

Finally got to take the Silvia out and have a run with the new MCA suspension on the weekend. Worth every cent is all i can say the car was awesome to drive, we unfortunately had to retire after stage 2 with a burst water line under the plenum that we couldnt fix in time but was 2nd outright behind an evo 9 untill then.

post-54017-1288573292_thumb.jpg

Finally got to take the Silvia out and have a run with the new MCA suspension on the weekend. Worth every cent is all i can say the car was awesome to drive, we unfortunately had to retire after stage 2 with a burst water line under the plenum that we couldnt fix in time but was 2nd outright behind an evo 9 untill then.

Go the S13!! So good to see a cool RWD car ripping it up against AWD evo/rexies!

Go the S13!! So good to see a cool RWD car ripping it up against AWD evo/rexies!
spewing about the retire Jase :laugh: next event you'll smash it!

Thanks guys, thats most likely it for me this year but will be back next year though ready to chase down the AWD's

In car from stage 1 can be found here

Well I finally got my R32 GTST out on the track for Time Attack at Lakeside on the weekend.

Never having driven the car I started off slow and was building up speed.

Blew a turbo and diff for the day and retired early.

Still had a great day and at least I didn't hit the wall. Thats racing.

Posted a 1:12.3400 for the day and still had an excellent day anyway.

post-40739-1288683198_thumb.jpg

nice man.

it always a good feeling taking a car out for the first time, shame bout the turbo though..

with the cage did you bump it with the hemet much? was it annoying? asking cause i think i will with mine.

Cage was a pain in the arse. I have the seat as low as I can. I am six foot and can't really see the front left side of the bonnet. The whole time my head was either resting or bouncing off the cage to the side above the window. Probably wouldn't without the padding. I will have to find a solution.

Madly sourcing parts to hopefully get another round in before the end of the year. Not sure I will but otherwise back in force next year.

i know its not tarmac but here is a pic of my dirt circuit chassis and engine build so far.

chassis runs quickchange rear end and full coilover plus 5th are suspension set up i have a ve commadore body to go over the chassis and the motor is a 308 with lots of goodies . i know its not a skyline or even a turbo lol so dont flame me :-)mmm says i cant upload this type of file ? any ideas its a bitmap bmp file ?

Edited by mid life crisis
i know its not tarmac but here is a pic of my dirt circuit chassis and engine build so far.

chassis runs quickchange rear end and full coilover plus 5th are suspension set up i have a ve commadore body to go over the chassis and the motor is a 308 with lots of goodies . i know its not a skyline or even a turbo lol so dont flame me :-)mmm says i cant upload this type of file ? any ideas its a bitmap bmp file ?

Sounds interesting. Try opening the bmp in Microsoft Paint, then go to the File menu > Save As - save window will show up, change the "Save as type" drop down menu to "Jpeg" - save it somewhere like My Documents and try uploading your newly created .jpg version.

try again lol

i know its not tarmac but here is a pic of my dirt circuit chassis and engine build so far.

chassis runs quickchange rear end and full coilover plus 5th are suspension set up i have a ve commadore body to go over the chassis and the motor is a 308 with lots of goodies . i know its not a skyline or even a turbo lol so dont flame me :-)

ah got it cheers all

Edited by mid life crisis

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...