Jump to content
SAU Community

Recommended Posts

i have bought a turbosmart type2 veeport bov and installed it on my skyline.

now my car keeps stalling and ive followed the instruction and tightened the spring but it still stalls,we have checked over it and theres no leaks,no blockages and no collapsed or twisted hose.

i got the spring as tight as it could go and it still stalled so i ended up taking it off and put the factory part back on and it runs perfect and doesnt stall and now i have wasted $400 on the adapter and bov.

im confused to why it stalls,hope yous can help me out.

The car is overfuelling due to the ATMO BOV.

The car expects the re-circ BOV to be there, its tuned for it.

Hence when you put it back it works fine.

So you have two choices.

Get a ECU & tune it ($1500)

Or go back to the stock one... which is is how Nissan intended it to be :D

Nothing wrong with the stock BOV so not really sure why you would want to change it anyhow.

The car is overfuelling due to the ATMO BOV.

The car expects the re-circ BOV to be there, its tuned for it.

Hence when you put it back it works fine.

So you have two choices.

Get a ECU & tune it ($1500)

Or go back to the stock one... which is is how Nissan intended it to be :D

Nothing wrong with the stock BOV so not really sure why you would want to change it anyhow.

thanks for the info.

im having the same problem with my turbosmart BOV but i have set it up so its set to recirc and its still stalling i have no idea whats goin on with it and im looking at being in the same boat as blitz becuz im gunna have to put the stocker back on or get an aftermarket ecu and tune (better start saving lol)

installing a HKS Fuel Cut Defender should override this problem? i think.

i experienced the same with my Blitz. I didnt mind the stalling every now and then, but i removed it to avoid the boys in blue.

The stock one does its job well enough!

as previously mentioned.. maybe investigate if you can adapt that BOV back to a plumb back .

also vac leaks can be quite hard to track down .. make sure you look for cracks at the places where other pipes join the inlet ( if there are any )

to be honest I was really impressed by the stock recirc valve on the rb25det NEO .. looked very well made! and at least if you have a recirc BOV the boys in blue have got one less thing to bend you over for !

and if you have a pod you should still hear the BOV noise.

ive heard alot of specualtion, but how much boost can a standard r32 gtst bov handle?

has anyone had a problem running 17-18 psi thru one?

im ready to put my stocka back on and see if it helps with the stalling..

ive heard alot of specualtion, but how much boost can a standard r32 gtst bov handle?

has anyone had a problem running 17-18 psi thru one?

im ready to put my stocka back on and see if it helps with the stalling..

From what I've read on SAU, the standard 32 gtst bov can handle about 14psi before it starts to leak if I remember correctly. If you want to run the standard plumb back system, I think you can just get the GTR's bov and put it in its place. They handle up to about 20-ish psi.

Feel free to correct me.

Its wierd mine has worked fine on the car and it has never stalled. Might change it back just cos it gets annoying sometimes. Did you make sure you used the gasket between the bov and the intake pipe?

  • 8 months later...
  • 16 years later...

My tuner told me this as well that the reason the car will stall is because it has a AFM system, he said it I want to do it properly I need to delete that system, he said I can try it though to see how it goes. My BOV recirculates btw (can hear flutter sometimes though), how do s15's and stuff not stall and they also have the AFM system? I was considering blocking it off for ovbious reasons but was hesistant because of the above.

1 minute ago, GTSBoy said:

By changing to a Halaltech and not having an AFM, typically. Or, they stall or otherwise carry on.

A lot of them are driven by p platers with stock ecu's lol. When does the stalling usually happen is it high speeds?

Edited by silviaz
On 10/31/2024 at 10:12 AM, silviaz said:

My tuner told me this as well that the reason the car will stall is because it has a AFM system, he said it I want to do it properly I need to delete that system, he said I can try it though to see how it goes. My BOV recirculates btw (can hear flutter sometimes though), how do s15's and stuff not stall and they also have the AFM system? I was considering blocking it off for ovbious reasons but was hesistant because of the above.

If you block off the BOV entirely you will get reversion out of the MAF and get a lean spike instead of a rich spike as the MAF double-counts the airflow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...