Jump to content
SAU Community

Recommended Posts

  • Replies 204
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

For all those who bought, have been informed of a feature available but not in the manual.

-If you connect the orange wire (normally earthed) to the reverse signal wire (12V), it will switch the picture to AV1 when reverse is selected, for the purpose of viewing a reverse camera. NTSC cams only for Stageas of course.

cheers

Big thanks to Chook for my unit. :thumbsup: I had heaps of questions about the unit and the install process and he helped me with every step. My install went relatively smoothy once we worked out how to pull all the panels out.

I have found that I have no car acceleration interference noise when I use the tv side of the unit. I used expensive 50cm wires for that connection, however, I have a seperate dvd (cheapo) unit in the back seat with seperate screens for the kids, I had to use longer cables, and they were of pretty ordinary quality. The result? I get heaps of interference noise when I switch the unit to the input from the dvd drive. I'm trying to decide whether to rip apart the boot again and replace the wires with some better quality cable, or install a noise suppressor, this is not the units fault I must stress.

I did have one other issue today tho, all of a sudden it would not get any signal from any station, so I performed the auto scan again, and it found no stations at all. Odd I thought, maybe the anntenas had shorted out?? So I was about to pull it all out and check my wiring again, but I noticed the reset switch on it, I hit that, and the auto scan came up with all the channels again no problem. So, I'm not sure what caused that, but a simple reset seemed to work, I know my home DVB locks up almost daily, I guess thats the digital age for ya!

Other than that the unit works quite well, its solidly built, top quality and keeps a steady picture going even with fairly bad signal strength (52%) :down:

Cheers,

Jeff

Thanks for the update chook - great support considering this is just a group buy! Mine is working perfectly (no issues with resets or anything else). I still have reception challenges at some deep spots near my house but the reception is much better than the previous unit I had in there.

Thanks for the update chook - great support considering this is just a group buy! Mine is working perfectly (no issues with resets or anything else). I still have reception challenges at some deep spots near my house but the reception is much better than the previous unit I had in there.

What's your aerial setup ? S1, pity you dont have the S2 amplified setup ?

  • 2 weeks later...

I pulled apart my dash today and found that I have the R-spec over ride but the switch has been cut off.

Can anyone suggest what would be a suitable button ans how would it get wired? There are 4 wires in the lead to the switch (or where it once was) and they are coloured, Red, Black, White & Yellow.

Cheers

Andy

I pulled apart my dash today and found that I have the R-spec over ride but the switch has been cut off.

Can anyone suggest what would be a suitable button ans how would it get wired? There are 4 wires in the lead to the switch (or where it once was) and they are coloured, Red, Black, White & Yellow.

Cheers

Andy

What is the R-spec over ride ? Sounds cool

Edited by danwatt
What is the R-spec over ride ? Sounds cool

Have a look on the 1st page of this thread. Chook posted a picture of the unit. It allows the TV to be used whilst driving.

Cheers

Andy

Have a look on the 1st page of this thread. Chook posted a picture of the unit. It allows the TV to be used whilst driving.

Cheers

Andy

You driving an M35 ? My car's screen works whilst driving and Im positive that there is no Over-ride unit installed. I think I have had all the interior in pieces looking for various wires/faults.

You driving an M35 ? My car's screen works whilst driving and Im positive that there is no Over-ride unit installed. I think I have had all the interior in pieces looking for various wires/faults.

Yes driving an nm35 ARX. Sounds like your has been fixrd to be visable all the time.

Yes driving an nm35 ARX. Sounds like your has been fixrd to be visable all the time.

R you sure that its not a setting through the display menu and the TV menu on the car ?

Edited by danwatt
R you sure that its not a setting through the display menu and the TV menue on the car ?

Pretty sure but then again I was able to get the screen working for a while after I played around with some menu settings. No idea what i did. Some how I changed it back again. The only obvious sign was that when looking at the GPS it would not track the car on the screen whilst it allowed the TV to work.

Pretty sure but then again I was able to get the screen working for a while after I played around with some menu settings. No idea what i did. Some how I changed it back again. The only obvious sign was that when looking at the GPS it would not track the car on the screen whilst it allowed the TV to work.

I will check out the setting on my screen and let you know, both the TV button Screen and the display button Screen

I dont know if this will help but have a look at the attached.

I can play movies when stoped and hand brake on like this but once hand brake is release the sceen goes back to navigation.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...