Jump to content
SAU Community

Recommended Posts

I've tried searching but couldn't find any solid info.

What are the 'extra's' so to speak that the 94 R32 GTR's have over 89,90,91,92,93 models?

I've heard rumor's that the motor's have the crank collar and the car has slightly bigger/better front brake's but as i said i can't find any confirmation.

Cheers in advance.

Link to comment
https://www.sau.com.au/forums/topic/217460-1994-r32-gtr/
Share on other sites

Hey mate...

93 onwards got the 33 GTR crank... but the snout to oil pump problem was still there.. It also got the pull type clutch rather then push.

r u sure about the clutch?

cause when looking for a clutch for my rb25 last year i found it didn't matter whether it was push/pull?

so its still worth getting the crank collars for the later model 32's?

Link to comment
https://www.sau.com.au/forums/topic/217460-1994-r32-gtr/#findComment-3839336
Share on other sites

they all got cross drilled brakes - all base model r32 gtr were the same brakes, the vspecs came with brembos same as 33 and 34 gtr

late r32s had longer crank drive for oil pump as said above, pull type clutch (yes same gear box as 33 gtr series 1 and 2, but 33 series 3 was different). different colour dash lights. side intrusion bars in the doors. cut outs in the front bumper reo bar for n1 ari ducts.

thats all I can think of.

But by now none of that is worth anything - even a 94 gtr is 14 years old so its not like the age will make much difference. If you are looking to buy one don't pay too much extra

Link to comment
https://www.sau.com.au/forums/topic/217460-1994-r32-gtr/#findComment-3841067
Share on other sites

nah he means they have the cutouts in the reo behind the bumper, so if/when you want to put in the N1 vents no need to cut the reo. :banana:

Yeah in a rare moment of clarity I think I understand. :laugh:

Anyway, here is a photo of a completely random 94 model. The cut outs don't look especially factory....

post-5134-1210034286_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/217460-1994-r32-gtr/#findComment-3845641
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...