Jump to content
SAU Community

Recommended Posts

when i was using Caltex, they were bang on E70 the whole time (except for one batch in the dead of winter being bout E65)

which reminds me, i need to check with Caltex if they've switched to 85% - you could always buy a sensor, not run flex-fuel but just use it as a monitoring tool.

hahah, yeah that's true. just buy straight ethanol and mix yourself! :D

but for normal tunes, a variation of E% a few in either direction isn't going to make a difference. Don't think Trent has anything smaller than a 5% change resulting in any timing/fueling change on my maps

  • 5 weeks later...

The turbo is still 600hp rated though, now matter what CR you have.

The only way to make that power with a 35 frame is if it is a hybrid, like a 3566 or similar with a big A/R and judging by that dyno graph it would have to be because that is a laggy curve for a 35R on a 3L.

Even still, 500kw Thread: ACCESS DENIED.

The turbo is still 600hp rated though, now matter what CR you have.

The only way to make that power with a 35 frame is if it is a hybrid, like a 3566 or similar with a big A/R and judging by that dyno graph it would have to be because that is a laggy curve for a 35R on a 3L.

Even still, 500kw Thread: ACCESS DENIED.

It's a GTX53R not a normal GT35R so it does flow another 70odd hp more...

In saying that the results are a little eyebrow raising and also don't fit into this thread

Well last time you posted then 490rwkw result you only ran 136mph... :merli:

Time to go back to the strip and see if you'll actually get near 140mph, they be the results we wanna see

Either way it's not 500rwkw - so have moved the posts to the 400rwkw thread.

  • 1 month later...

Well last time you posted then 490rwkw result you only ran 136mph... :merli:

Time to go back to the strip and see if you'll actually get near 140mph, they be the results we wanna see

Either way it's not 500rwkw - so have moved the posts to the 400rwkw thread.

car was making 431rwkw when i ran 10.8 @ 138 MPH

i have since gone to a new tuner and hence new results.

U know who micks motorsport is?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...