Jump to content
SAU Community

Recommended Posts

yeah the thizzle figure is very questionable, i would take it with a grain of salt

its the only 300kw GT-RS ive ever seen so wouldnt even use it as comparison

it must have some other mods we dont know about, ie diff gears, different gear ratios, different dyno settings

could be a million things, wouldnt worry too much

most GT-RS's make 260kw and cap there

but the main benefit of the GT-RS is the average power and response

  • Replies 489
  • Created
  • Last Reply

Top Posters In This Topic

Has this question been addressed? Also, what is the equivalent PULP RON (if such a comparison can be made)?

a few motors have been pulled down with no ill effects. e85 also loses power before the knock becomes serious so the tune isn't as much of a knife edge as pulp.

people have been claiming a ron figure of 108-110

a few motors have been pulled down with no ill effects. e85 also loses power before the knock becomes serious so the tune isn't as much of a knife edge as pulp.

people have been claiming a ron figure of 108-110

I like that RON. Sounds very promising. The only thing i have heard is the 10% ethanol stuff can foul up plugs on some cars. I personally never had any issues running boost98 from united in the vl or the 32. Both cars just chewed through it alot quicker.

well the tank is at 1/4 full (my standard refill point) and i have done 220k's, nomally i get 320...

so in essence.... if the price of e85 2/3 of the price of 98 then you are getting a free power increase..... and if its below 2/3 you are actually SAVING $$$

good result, how much timing did you settle on at full load and what afr?

sorry... forgot bout this one

timing 39deg (decided to look @ hand cont... lol)

afr's cant remember the exact figure

my filter flowed fine after 6 months use, I think each car will be different, mates blocked up after only a few months, pull it off and blow thru it, compare to a new one!

Edited by 180or200

I have been very keen to jump onto the e85 band wagon, and have followed this and another similar thread. My big question or thing I would be interested to see...is both tunes one on 98 and other on e85 with same power outputs.

It is proven that e85 will make more power, but how about the engine using less effort to make the same power? Less boost, less stress on components, maybe lower intake temps? then we can compare effects on engine life, fuel efficiency, engine/oil temps and see the other benefits just not more power from e85.

If you can use more timing and less boost to get the same power would you be using less fuel?

Paul.

i doubt it as my car was lean as f**k when it was first started and needed a decent whacck of fuel to compensate... also with the better response its way more tempting to put your foot down :P

just to let all you victorians know...

i rang united head orifice and asked where e85 was stocked and was told hoppers crossing AND buleen... they even gave me the bulleen address!

i went to buleen united today and the is NO e85 pump! (i asked the guy WTF and the only 2 english words he could say were "united" and "boost" lol)

so in vic atm it is ONLY hoppers crossing!

they did say there is talk of a bigger rollout soon, but not in the next few weeks

First post, so I thought it should make a contribution to the group.

Just been looking on the United Petroleum web page for locations. Noticed that the Kingsway (South Melbourne) United site is listed as stocking E85 fuel. This site is at 151 Kingsway, South Melbourne, 3205 and is listed as being open 24 hours a day - for all the night owls.

Here is a link:

http://www.unitedpetroleum.com.au/distributor-information.asp?IDstore=464

ah i didnt know that the kings way one would have E85

thats a big difference, as hoppers is homo-spec

yeah hamish the tune you have is locked, when the PFC is locked, you get 0's everywhere

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • No. GKTech arms have spherical bearings in them. No bushes. You will not need bushes for those arms. The sphericals are a bit of a maintenance nightmare. I have replaced all of mine several times in the 5 or so years I've had them, and I have the arms out regularly to clean and lube the balls. Worth the pain on an R32, because the standard arm design is trash. If you need the camber adjustment, there are other options (than the GKTech ones), although I would still lean towards and prefer the GKTech ones, even with the maintenance load of the sphericals. The caster adjustment is also highly valuable, allowing for setting the car up to drive straight. There are a million options for these, including the GKTech ones. I've had Tein rods on mine for 20 years and the balls are much less trouble in that location. Never given me a moment's pain. All positives, no negatives. I consider them compulsory.
    • Lol yeah I ordered the clips mentioned and as far as the amayama diagrams go i think thats all I'll need. Fogured id ask, sometimes people's first hand experience doesnt always match up to diagrams haha, i guess I'll wing it and worse comes to worse I'll just deal with it as I go
    • Thanks for all that information I appreciate it. To answer your questions: - Yep that's what I mean. These guys are professional painters to so I must be missing something. It's a bit hard to explain. - With the primer landing on clearcoat, I make sure that the surrounding clearcoat is scuffed to 240 grit as my epoxy primer says that I only need to sand the area to 240 grit. - Yeah so similar to the first question, assuming that the paint landed on the unscuffed clearcoat because I've seen that happen. - Yep I want to prep the surface in that order. Only reason because epoxy primer will protect it from rust and I need that atm with this crappy Sydney weather. I think I was worried about time, if I try to put the filler down but screw it up somehow and I don't have time to sand it off and reapply it then need to put primer later that it might start to rust again so I wanted to apply the primer as quick as possible to not deal with rust.  - I just deleted some answers, I just realised after watching a video and what you said about looking at the data sheet, that I need to read the data sheet on the specific filler I'm using. It's possible now that I put epoxy primer first was a waste of time and need to go to bare metal lol
    • I did. I went to a suspension guy and he told me because I don't have adjustable camber arms it's the reason why my car veers towards the left if I take my hands off the wheel but if I drive my other every day car and take my hands off the steering wheel it goes completely straight. I think it's common with Skyline's. In order to fix the problem, I likely need gktech camber arms then nismo bushes since I have poly bushes atm, then a wheel alignment after that. With my car if I take my hands off the steering wheel on a really bumpy road before stopping at a light I have to hold my steering wheel somewhat tight otherwise my car will legit just go completely in the other direction quite quickly and I'll slam into something lol instead of stopping straight. I Believe this YouTuber had the same issue and fixed it with gktech arms. At timestmap 6:05 he talks about how the car doesn't veer anymore after installing these arms.  
    • hello! does anyone have a schematic that shows how to test the blower motor resistor for the vac system? i believe the part# is 27761-15U00. I think the resistor is toast, but would like to be able to test it somehow before i embark on the journey to find a new one. cheers! 27761-15U00
×
×
  • Create New...