Jump to content
SAU Community

Recommended Posts

You are actually moving an engine from the wrecker in the trunk of a Skyline??

;):thumbsup:

ons only, so Power vs Boost generated from it would be identical to any other healthy standard RB25dets.

Engine:

96 model RB25det engine bought from local wrecker.

1.jpg

The compressor map with the standard high flow would be identical as:

http://www.turbobygarrett.com/turbobygarre...60-15comp_e.jpg

Since its running the same size wheel in same size housing.

Further updates:

The ARP bolts, Bearings and full Gasket set cost $691.

gaskets.jpg

Engine come back horned and cleaned ($535). The job was abit rough thou, I spent hours buffing out the left over residuals from previous head gasket, Which I paid to get it cleaned. Any way:

Engine block with pistons back in and head assembled:

engine.jpg

engine2.jpg

piston.jpg

engine2-1.jpg

engine3.jpg

engine4.jpg

engine5.jpg

head.jpg

Well original goal of building this engine is not for that wow factor, I just need a very solid standard engine to evaluate max power out put on 98 fuel for all high flow profiles and bolton ATR43s. So Power vs Boost vs RPM would be identical with the same turbo on any standard RB25dets. This is also a None Neo motor, Neo engines would pickup better power and response.

Results with fully moded head, cams, and manifold would be deceptive as no one else has the same mod. But I will get them to run with race fuel and Nos after the evaluation for abit of fun :whistling: .

Link G4 Ecu

hiflowed turbo

550cc injectors

3" dump/exhaust gutted cat

intercooler

bosch 040 fuel pump

5puk exceedy clutch

and wind that up to 20psi and watch the figures climb haha

Hi Guys, I'v just bought a fully stock R33 of JSA 2 weeks ago. I'm looking to get me turbo high flowed and make some power. Can you give me a list of recommended mods? Cheers.

If its just been complianced there are few of things to be done:

1. Install a front mount cooler (we can supply).

2. Install a strong clutch (recommend Xtreme clutch kits at Ace Brakes ) if your is stock.

3. Install a full 3inch turbo back exhaust with a honeycomb cat. (JSA are Xforce dealers they should have plenty).

4. Get a set of 550cc / 700cc injectors (Try Cjmotors).

5. Get a Z32 AFM. Try Japart or see if JSA's got one.

6. Get a 3inch metal induction pipe made up (Try Glenroy exhaust) and get your self a good pod filter.

7. Get a PFC or Z32 ECU with Nistune chip (You can get that done at my recommended tuners).

8. Bring pass your stock turbo and have a chat, we have few different profiles and turbine housings to choice from.

9. With few hours of Dyno time at Dr.drift or Status your car would be pretty sweet to drive.

Another update:

This is a OP6 high flow that we did for a customer's R33 (none Neo engine) earlier using our updated turbine wheel. It made 241rwkws at 15psi full boost by 3450RPMs with 98 fuel. I'm pretty happy with it, Dyno sheet showing results of tuned maps before and after high flow. It made more power every where without more lag.

The other thing that I'm pleased with is the power curve which sits lot more gradual instead of linear. So the wheels will be able to convert lot more of those energy onto acceleration momentum.

op6highflow241rwkw.jpg

Hi mate, am interested in a Hi Flow Turbo..

looking at running around 230rwkw..

How much does it cost to Hi-flow my current turbo I got a gT-t r34.

& do i take it to my mechanic for a straight bolt on?

I have a new front mount intercooler,

Clutch.

Do i need an ECU?

Whats the cheapest ECU I Can get?

The cost to high flow is $960 inc GST and braided oil feeding line. Every thing bolt back on. The cheapest ECU option would be getting a Nistune ECU installed and you need a set of at least 550cc injectors and a Z32 AFM. Will get you 230rwkws with 14psi of boost.

With The Nistune ECU you can order direct from Matt on: [email protected] its $350 installed. Some of your local tuners can also install it as a package with the tune.

Also some update with my engine build:

The engine build has been complete and it is now back into the car. How ever it floods it self every time I crank. I guess I have to toll it to Sam to play with the map. Not having much luck with it this time.

Hi Stao,

i been thinking to Hiflow my turbo for a while now, just wondering once u guys Hiflow it do i need to upgrade my ECU straight away

or car i still drive on it till i get around to buy my new ecu

thanks

I would assume you shouldn't have any problems driving it around on low boost with standard ECU for a while.

Though having said that, it comes with a high pressure actuator, so you will have a lot of trouble driving it around without overboosting.

I will be receiving mine soon, and will need to drive it on stock ECU to the tuner after fitting. I'm not looking forward to that part lol.

I'd recommend (as I'm sure others will too) to just save up some more, and get it done at the same time as other necessary supporting mods (injectors, fuel pump and ECU)

Hi Stao,

i been thinking to Hiflow my turbo for a while now, just wondering once u guys Hiflow it do i need to upgrade my ECU straight away

or car i still drive on it till i get around to buy my new ecu

thanks

Once turbo is high flowed you can still run about 10psi with stock ECU and 98 fuel. There will still be a very noticeable difference in power and torque. It is recommended to go for a aftermarket ecu some injectors and etc to get the full potential of your car.

Some updates from yesterday:

Engine's build has been completed.

enginewbelt.jpg

enginenew3.jpg.JPG

enginenew2.jpg.JPG

Taking the old engine out with respect to its 6 month service.

engineold.jpg.JPG

turboold.jpg.JPG

engineout.jpg.JPG

New engine is dumped in, alone with a evaluation subject: OP6 high flow

enginein.jpg.JPG

turbonew.jpg.JPG

How ever the engine fouls plug on crank. Tolled it to Dr.drift today and hopping for the best

Stao/anyone who may know:

I am intending on at the very least running this as my temp setup until I can get a hard intake setup made, will this flow 18psi through an ATR43G2 without causing restriction?

3" turbo inlet > 3" to 2.5" silicon adapter > standard R33 intake piping with 3" steel pipe mod to stop sucking closed > pod filter

the 2.5" silicon after the turbo is my concern, but I've heard that it won't cause an airflow problem as long as the intake piping doesn't suck itself closed.

Confirm/deny? Thanks :ermm:

Here are 3x dyno sheets for your reference as stock intake system, stock intake pipe with metal insert didn't work. I also believe your friend Pat experienced very difference result before and after upgrading to 3inch metal intake with pod. His comments are in page 39.

Results:

1. ATR43G2 Stock intake pipe with air box no filter. Intake pipe sucking shut.

atr43g3badrun.jpg

2. ATR45 running stock intake pipe with metal sleeve stopping it from shutting with pod filter. (left)

ATR45 running 3inch metal intake pipe with pod filter. (right)

The sleeve insert run ended early as it not only restricting power, it did some thing strange (knocking?) and inconsistency in AFM reading. This run ended early.

atr45intakecompare.JPG

So please use a 3 inch or better 4 inch intake pipe with a good flow pod filter. Or at least use that for tuning.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...