Jump to content
SAU Community

Recommended Posts

You may as well finish off the steps that have been suggested.

Then you will need to find another e-clip before you should boost it. You can still drive it as the rod will stay there, just dont boost it as it may fall off and if you nail it will go infinity boost. The e-clip should just slide out sidewards.

Yeh I've completed the steps, it appears the actuator was already perfectly adjusted as I didn't have to adjust it at all according to how Stao said to do it, so I can rule that out as a possible cause of my trouble. In the process of getting the rod back onto the arm now but fark me it's hard lol. Where can I get another e-clip from???

Edited by Hanaldo

Ok sweet, thanks mate. I suppose for size I can just take the broken eclip along?

I can not get this farkin rod back on the wastegate lol. Kind of emasculating, I can't even get it to budge :blush:

repco, sprint auto parts, autobarn, etc. the clip should be like $0.50c

dont worry, lost mine recently as well.

to put it back on, it'll be hard as fark, use a pair of pliers to pull like buggery, slip it on a bit, and hammer it down into place

take a off-boost drive down to your local auto store and grab a new clip. install with pliers.

all the best.

cant put my finger on what is wrong in your application. no suggestions other than retune the nistune ecu elsewhere (different dyno/operator)

bad luck about the costs Hanaldo. Not a nice feeling Im sure, trying to keep to a budget and then finding you've gone over budget with no result to speak of

All good, got it back on. Arms are scratched to shit now lol. Will have to wait until tomorrow to get a new clip, everything is shut now.

Anyway, can cross wastegate not closing properly off the list.

Here's today's tune from ATR43G2 in .63 rear housing.

Dark blue is no boost controller straight off the actuator, Max of 255rwkws @ 17psi

Light blue is with Wastegate controller, 267rwkws @ 19psi.

Driving ability is pretty good, and very agressive. Its a good little turbo for around 250rwkws mark.

Dyno run is based on 9 sec ramp timing.

atr43g2267rwkws.jpg

atr43g2267rwkwboost.jpg

I've got a strange dip around 3500RPMs not sure if its VCT related, but doesn't seems to be felt on road.

Almost identical Compare to same turbo based on an earlier run on a R34:

260rwkwsop6hf.JPG

Also we did multiple runs today, didn't have any issues with it pinning with high boost.

If it does pin at 16psi It generally means if the turbo's having issues sucking in or dispatching air (into engine and into exhaust). Lot of shaft speed losts when this happens, and exhaust blade will act as blockage for the engine to pin.

Hanaldo I enlarged your sheet it appeared to run on 14psi??

Also we did multiple runs today, didn't have any issues with it pinning with high boost.

If it does pin at 16psi It generally means if the turbo's having issues sucking in or dispatching air (into engine and into exhaust). Lot of shaft speed losts when this happens, and exhaust blade will act as blockage for the engine to pin.

Hanaldo I enlarged your sheet it appeared to run on 14psi??

What would cause that? Restriction I imagine? Where else could there be a restriction? Everything seems to be pointing to a restriction of some kind. I pulled all my intake and cooler piping off today, made sure none of it was blocked. Did another pressure drop test across the intercooler, only about 1psi difference. Did all hose clamps back up tightly and made sure everything was sealed, no vacuum leaks.

Stao which graph is that? I don't have a print out of boost?

I'm not sure. From what I've seen this issue happened to people whom made crappy metal filled intake pipes (also blamed the turbo). Very similar to yours scenario, which runs on very low timing, can't control boost, and any thing done to fix it made the engine pining worse. Check page 57.

Yours looks alike but doesn’t mean its the definit same problem.

My R33 S2 w. standard turbo makes [email protected] at the clutch, but that is as far as it goes :)

16PSI at 3000 rpm .... :)

Nistune, Cams, De-Cat, etc ...

a stock turbo'd rb25 making "way over 200rwkw" on 14psi... stao, whatever you are on can you pls organise me a pound? ;)

also trent's dyno with the appropriate correction reads the same as a dyno dynamics, my car has backed this up on 3-4 dyno's now

My R33 S2 w. standard turbo makes [email protected] at the clutch, but that is as far as it goes :)

16PSI at 3000 rpm .... :)

Nistune, Cams, De-Cat, etc ...

yea, which would amount to all of 190-200kw at the treads champ.

We talk rear wheel kw here, as measured off the rollers or hubs.

240kw is going to net you around 200-220rwkw.

You sure it is the stocker turbo? You realise the exhaust wheel is made of glass, well ok ceramic. Anything after 12PSI is asking to have the exhaust wheel end up down the exhaust.

Tao it would be interesting to see the ATR43G2 in .63 with some boost control. Comparing it to the 3071R's in the results thread it is laking in response a little, even against the .82 rear. And

youre run has is starting off at 1.4bar and bleeding off, where as the 3071's run a pretty constant 1.1-2bar'ish

yea, which would amount to all of 190-200kw at the treads champ.

I have the exact figure somewhere .. but I sure did not lose 50KW on the way to the wheels :)

But as said, this is as good as it gets with the standard turbo, and I never stress the turbine for too long ..

Hi!

Yes, it is the standard turbine ..

I ran this type of boost for over 14 months now ...

But as said, the turbo is not overly stressed since I rarely use the full boost for long.

Also I only have a SMIC from the R34 ..

I heard many stories about how much this unit can take, eventually the turbo might die :(

So I am already doing the research for a new turbo if my old unit should fail me one day ..

I definitely want to keep the low lag of the standard unit, so 14.7 PSI at 3000rpm is a must.

Attached is an older dyno-run.

Ignore Torque figure / shape, since the operator did not tie my car down well enough

We talk rear wheel kw here, as measured off the rollers or hubs.

240kw is going to net you around 200-220rwkw.

You sure it is the stocker turbo? You realise the exhaust wheel is made of glass, well ok ceramic. Anything after 12PSI is asking to have the exhaust wheel end up down the exhaust.

post-33912-0-54170100-1301698346_thumb.jpg

Edited by Torques

Tao it would be interesting to see the ATR43G2 in .63 with some boost control. Comparing it to the 3071R's in the results thread it is laking in response a little, even against the .82 rear. youre run has is starting off at 1.4bar and bleeding off, where as the 3071's run a pretty constant 1.1-2bar'ish

The one you've seen (based on status reading) are on 12 sec ramp timing, I've already tried to compare those at status,. mine's on 9 sec with current software. Based on 9 sec ramp they almost the same. information and comparision on dyno ramp is in page 73.

That is a very standard G2. The ATR43SS series with FNT turbine is probably some thing to look at if you really want the power curve to stand out.

I've running a high pressure actautor so won't be able to run any thing less then 20psi. The R34 Neo motor was running on 15psi and made the same power every where as mine which is interesting.

Hanaldo, Ive said this a few times on the forum yet a few years back I experienced a problem similar to yours.

The issue was I had an 80mm front pipe and a 76mm cat. The 4mm smaller ID caused all sorts of issues and resulted in about 60rwkw less than expected. We swapped to a fairly standard 80mm cat and got the 60rwkw back.

Im not suggesting your cat is bad or the wrong size, but im suspicious about your custom made dump. For the money I highly recommend you grab a justjap bellmouth dump, they are only $189 brand new... Im not sure how much shipping to WA will be though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...