Jump to content
SAU Community

Recommended Posts

For 1/4 mile interest sake, I run a atr43g3 .63 on an RB20, on a very safe tune 217rwkw on 18psi (as the car does track work). Ran a 13.0 @ 109mph on Nankang street tyres.

awesome! what turbo is he running?

but still, aint no skylines down the 1/4 yet :O

1/4 mile times are also pretty pointless as you have way too many factors that differ from one run to the next, including car, driver, tune, tyres, track, weather, just because one person does xx.xx does not mean you, your tyres, your suspension or any other factor will do the same, some will be faster and some will be slower.

1/4 mile times are also pretty pointless as you have way too many factors that differ from one run to the next, including car, driver, tune, tyres, track, weather, just because one person does xx.xx does not mean you, your tyres, your suspension or any other factor will do the same, some will be faster and some will be slower.

yes the 1/4 time itself varies a lot with tyres, how good the driver is at getting the car off the line etc etc.

However the mph gives a very good indication of the power/weight of the car. Given most of our cars would be similar weight it will show very well the power of the car.

You can do 10 runs ranging from poor launchs to your best launch and as long as you rev out the gears and change fairly well your mph will only vary by 1-2mph.

Can be much better then comparing dyno sheets from different types of dyno in different states etc. I just cbf getting down to calder haha and its normally on a friday night.

I don't give a flying fungooloo about all the "variables" ,it is still good to see times not just printouts is all I'm saying..

Lots of things vary..you know yourself Harey, your car isnt pulling as much power with the same turbo as Tao, but it is still interesting to see your results none the less..And it would be even more interesting if you had a 1/4 mile time slip to go with each of those turbos you have tried....

Personally i just think it is more interesting to see how it performs on a track than any paper printout..

Trap speeds would certainly back up power figures but once again it'll only really back up the peak figure and not say much about how the car drives.

I like dyno sheets as it gives a good indication of if its got good midrange punch, lots of top end etc etc

If it was auto, with a converter yes, the mph would only show a peak figure, however seeing as most guys are manual, the powerband under the curve

will still be shown in the mph. Especially the difference between 1/8 to 1/4 traps depending on turbos

cheers

darren

Edited by jet_r31

Most stock boxes with typical 4.1 -> 4.4 diffs would be able to keep the revs between 5 and 7k though yeah? Even the laggiest turbo would be on full song down the strip then.

Most stock boxes with typical 4.1 -> 4.4 diffs would be able to keep the revs between 5 and 7k though yeah? Even the laggiest turbo would be on full song down the strip then.

depends on a few things, but between 5 to 7 grand happens 4 times, 3 times in a under 124mph trapping gtr generally, and even if they make the same peak power at 7000rpm

one might be down 20rwkw between say 5-6 grand, that car might pull a car length every gear change and run 2-3mph more through the traps

In a auto with a converter, it woudn't really happen, the converter would flare to upper 6000rpm from start to finish and the cars would fairly even, thats basically how it works

Had a mates gtr yrs ago, had same peak power, lillte bit more down low, every gearchange he would pull 1 car then it would stay the same, then change gear, pull one car instantly then stay same was HIGHLY annoying, haha

cheers

darren

Edited by jet_r31

front.jpg.JPG

Got this in the mail today...

I am still waiting for my car to get here so will be a while before i have any results

But are going to run it with some pre turbo water /meth injection and some Tomei 260 9.15poncams and let it eat on at least 22-23psi.

If it make 300rwkw through a auto i will be happy

What would a 300rwkw stagea trap, what do they weigh with double sunroofs? 1650kg, my goal was 115mph

cheers

darren

Edited by jet_r31

7 blade comp :blink:

Its not a 76mm garrett so that means very little lol

As for pre turbo water injection, you may need to look into that as ive heard its no good for the compressor. Post turbo might be better.

Just for informations sake, specs on the corona.

1jz-gte

Hypergear TR44 turbo

Trust exhaust manifold

Trust 50mm wastegate

3" mandrel bent exhaust

500X300X76mm intercooler

3" intercooler piping

GFB Mach 1 BOV

2 front mounted gearbox oil coolers

Microtech LT12s and X6 igniter

X2 Excel radiator

No power steering or Air conditioning pumps

Techedge 2EO wideband o2 sensor

NOS kit (50 hp jets)

Greddy Profec B II

Driveline

Custom tailshaft with tail shaft loop

Hiace diff with 4.11 CIG locker Hilux centre.

New bushes for all diff mountings

A340E auto controlled by MV autos manualised shift box

2500rpm torque converter with lockup

Edited by lilcrash

Its not a 76mm garrett so that means very little lol

As for pre turbo water injection, you may need to look into that as ive heard its no good for the compressor. Post turbo might be better.

Yeh i'm not to worried, i ran it that way on my R31 with no wear and my brother runs it that way on his gemini, with a 3082 just have to see how i go, depends on so many variables.

The turbo is the big hi-flow protoype stao built ages ago, made 320rwkw on around 23psi i think, and didn't get hot even with the .63 exhaust apparently

cheers

darren

This is the new SS2 prototype trail using the external gate turbine housing. It actually made about 300rpms better in response. how ever didn't help when the car caught in fire. lol. One of the rubber hose expanded under pressure and torched on the exhaust manifold. Well, made 293rwkws when fire broke out. lol. Will do a bit more trailing in later stages.

power.jpg

booost.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...